Specifications subject to change without notice.
ILA Series
Installation Line Array
WL2082-i
WL115-sw
Configuration
2½-way, bi-amp or tri-amp mode
4th order bandpass subwoofer
Transducers
High-frequency
Dual 50 W, 8
Ω
1" exit, 1.75" titanium diaphragm,
−
neodymium magnet assembly
Low-frequency
Dual 200 W, 16
Ω
8" woofer, 2" voice coil,
650 W, 8
Ω
15" woofer with a 4" voice coil, ceramic magnet assembly
neodymium magnet assembly, weather resistant cone
Frequency Response (±3 dB)
80 Hz – 20 kHz
37 Hz – 107 Hz
Frequency Range (-10 dB)
68 Hz – 22 kHz
35 Hz – 112 Hz
Nominal Impedance
HF: 16
Ω
−
LF bi-amp mode: 8
Ω
−
LF tri-amp mode: 16
Ω (
x 2)
LF: 8
Ω
Continuous Power Capacity
1
HF: 100 W / 200 W
−
LF bi-amp mode: 400 W / 800 W
−
LF tri-amp mode: 200 W / 400 W
(
x 2)
LF: 650 W / 1300 W
Sensitivity (1 W at 1 m)
HF: 106 dB
−
LF: 96 dB
LF: 96 dB
Maximum Output
HF: 126 dB / 132 dB
LF: 122 dB / 128 dB
LF: 124 dB / 130 dB
Nominal Coverage
H: 140°
−
V: dependent on number of elements used
−
Cabinet Type
Ported, elliptical / trapezoidal
4th order bandpass
Enclosure Material
HIPS (high impact polystyrene) with UV protectant
18 mm baltic birch plywood
Finish
Available in black (WL2082-i BLK) or white (WL2082-i WHT) paintable
Available in black (WL115-sw BLK) or white (WL115-sw WHT) paintable
Grille
Perforated, formed aluminum
−
Connectors
2 x NL8 in parallel
2 x NL8 in parallel
Pin Outs
Pins
Bi-Amp
Tri-Amp
Pins
1+/1-
NC
NC
1+/1-
Sub
2+/2-
NC
LF2
2+/2-
NC
3+/3-
LF
LF1
3+/3-
NC
4+/4-
HF
HF
4+/4-
NC
Attachment Points
Integral, side plate adjustable rigging system, vertical splay
Integral, non-adjustable (straight array only)
adjustable in 1° increments from 0° – 10°
Weight (Net / Shipping)
37 lb (16.8 kg) / 45 lb (20.45 kg)
111 lb (50.4 kg) / 121 lb (55 kg)
Dimensions (HWD)
11.8" x 27" x 13.4" (300 mm x 686 mm x 340 mm)
22.1" x 27" x 30.25" (561 mm x 686 mm x 768 mm)
Accessories Available
FB2082-i: Fly-bar for WL2082-i and WL115-sw. Available in black or white.
EB2082-i: Extension bar, allows WL115-sw to be suspended behind WL2082-i. Available in black or white.
PB2082-i: Pullback bar for WL2082-i. For use when pulling back the bottom of the array is necessary to achieve the desired angle.
Available in black or white.
QRP-KIT-1: Kit of four (4) Quick Release Pins for use in lieu of included bolts.
1) 2 hours, IEC specified noise
/ Recommended Power
Continuous / Peak (SPL at 1 m)
