background image

Input Signal

Frequency Response

20 Hz to 20 kHz, ±0.5 dB

10 Hz to 80 kHz, ±3 dB

Distortion

<0.01% THD+N @ +4 dBu out

(page input <0.03%)

Dynamic Range

>110 dB unweighted (20 Hz–20 kHz)

(page input >100 dB)

Polarity

In-phase or reversed

Level Control Range

-95.5 to 0 dB in 0.5 dB steps

Precision Attenuator Transients 

(“zipper noise”)

better than 112 dB below maximum output

Mute

>90 dB attenuation

Inputs

Program inputs 

16

Paging input 

1     Dedicated input with configurable 

routing to any or all 16 input sections

Monitor bus input 

1

Connector type 

“Phoenix-style” (a.k.a. “Euro-style”) 

detachable terminal blocks

Type Electronically 

balanced

Grounding 

All shield terminals connected 

to chassis

Nominal level 

1V/3V rms selectable (-10 dBV/+4 dBu)

Maximum level 

+21 dBu

Impedance 25 

k

balanced

Common-mode rejection 

Typical, >50 dB, 20 Hz-20 kHz 

Worst Case, >40 dB at 20 kHz

Crosstalk (inter-channel 

within DataPort pair) 

>75 dB separation (20 Hz–20 kHz)

Crosstalk (intra-channel 

between DataPorts) 

>90 dB separation, 20 Hz-20 kHz

measured with all inputs and 

outputs terminated

Outputs

Program outputs 

16 (via HD-15)

Connector type 

8 HD-15 DataPort connections

Cable type 

VGA monitor cable

1

Qualified length

2 meters

Monitor output

1

Connector

“Phoenix-style” (a.k.a. “Euro-style”) 

detachable terminal blocks

Type Electronically 

balanced

Grounding 

Shield terminal connected to chassis

Nominal level 

+4 dBu

Maximum level 

+21 dBu

Output impedance 

75

balanced

Output load 

600

min

Power Amplifier Output Monitoring

Output Short Detect

Senses load <1

for Stereo/Parallel modes; 

<2

Bridge Mono mode (default threshold)

Threshold is adjustable in software

Output Open Detect

Senses load >60

(default threshold)

Threshold is adjustable in software

Output Voltage Meter

Range automatically matches to 

amplifier model used

Output Current Meter 

Range automatically matches to  

amplifier model used

Amplifier Headroom 

Reports remaining available power  

Amplifier Gain

*

Calculates and reports amplifier gain

(knob setting)  

*Signal level must be higher than -32 dB, referenced to maximum output of amplifier

Power Amplifier Management

Power Amplifier Interface

Compatibility QSC 

DataPort-equipped 

amplifiers

Connector and cable 

HD-15 VGA cable

1

, 2 meters length

2

qualified (for longer runs, contact QSC’s

Technical Services Department)

Amplifiers

Up to 16 channels (8 DataPorts) of   

QSC DataPort-equipped amplifiers

Amplifier AC Power Control

AC mode control 

Switches amplifier between operate 

and standby mode 

AC power indicator

Indicates operate, standby, or 

power-down mode

Amplifier Status Monitor

Clip indicator 

Senses channel clip status

Protect indicator 

Senses amplifier protect status

Temperature meter 

Reports amplifier operating temperature 

Over-temp. alert

Software adjustable threshold (80°C default)

Control Room Foldback Monitoring

Number of Signal 

Monitoring Buses per CM16a

1

Number of Channels per CM16a

4    (Maximum number assigned

to monitor mix at one time)

Internal Signal Monitor Points 

(each with individual level controls)

Pre-fader input signal 

16

Post-fader input signal 

16

Power amplifier output 

16

Monitor Input 

Summed with internal monitor mix 

at unity gain

Monitor in to monitor out 

0 dB,  ±1 dB

Nominal level 

+4 dBu

Maximum level 

+21 dBu

Input impedance 

10k

balanced

Configuration 

Active balanced, shield connected to chassis

Common-mode rejection 

Worst case, >54 dB at 20 Hz rolling off to 

>40 dB at 20 kHz

Typical case, >50 dB 20 Hz-20 kHz

Output

Sum of external monitor input and signals

from internal monitor mix

Frequency response

20 Hz–20 kHz, ± 0.5 dB

Distortion

<.05% THD @ +4 dBu out

Dynamic range

>90.5 dB unweighted, 22 Hz–22 kHz

Noise floor

-90.5 dB

Nominal level

+4 dBu

Maximum level

+21 dBu

Output impedance

75

balanced

Output load

600

min

Configuration

Active balanced

RS-232 Port

Cable Type

Null-Modem (a.k.a. Laplink), female 9-pin 

D-sub chassis connector

Port Settings

Bits per Second

9600

Data Bits

8

Parity

none

Stop Bits

1

Flow Control

Xon/Xoff

Page Input

Specifications

Содержание Network Audio Systems







Отзывы: