QSC HPR151W, Руководство пользователя

Страница: 17 / 20

17
Specifications, Full Range Models
HPR152F HPR153F
Frequency Response, ±6dB 53-18k Hz 42-19k Hz
Frequency Range, -10dB limit 50-20k Hz 38-20k Hz
Maximum Peak SPL 135dB 133dB
Nominal coverage, H x V 90°x60° 90°x40°
Directivity Index 9.4 11.1
Directivity Factor 8.7 12.9
Transducer Description 15” (381mm) transducer with 3” (76mm) voice coil 15” (381mm) transducer with 3” (76mm) voice coil
1” (25mm) throat compression driver 6.5” (165mm) transducer with 1” (25mm) voice coil
1” (25mm) throat compression driver
Acoustic Crossover Freq. 2,000 Hz 500 and 2,000 Hz
Amp Power 400 Watts, low frequency 400 Watts, low frequency
100 Watts, high frequency 100 Watts, mid frequency
100 Watts, high frequency
Input Sensitivity 0.775 V
rms
(+0dBu) 0.775 V
rms
(+0dBu)
Input Headroom/Clipping 10 V
rms
(+22.2dBu) 10 V
rms
(+22.2dBu)
Input Connector/Impedance XLR female, 22k Ohm, balanced, line-level input XLR female, 22k Ohm, balanced, line-level input
(unbalanced, 11k Ohm) (unbalanced, 11k Ohm)
Output Connector XLR male, wired in parallel with Input connector XLR male, wired in parallel with Input connector
Controls, Indicators, and Gain control, 100 Hz low-cut filter switch, Front LED on/off switch, Limit/Clip (red LED), Signal presence (green LED), AC Power (blue LED),
Adjustments AC Power switch, AC circuit breaker
Protection, Agency certs. Thermal limiting, On/Off muting, power limiting, DC protection, short circuit protection, ultrasonic protection, RF protection, UL/CE listed
AC Power Requirements
AC Power Connector and Cordset Factory supplied IEC cordset: 6’ (2m) #18AWG 120V North American or European 230V cordset
Dimensions (height, width, depth) 32” (813mm) x 19” (485mm) x 18” (455mm) 45” (1137mm) x 19” (485mm) x 18” (455mm)
Installation Clearance Allow for 6.0” (152mm) of free space behind the enclosure to assure proper amplifier cooling
Weight 100 lb/45.4 kg 118 lb/53.5 kg
Finish and Grill Wear-resistant textured paint finish on plywood enclosure and powder-coated perforated steel grill
Notes:
1- Maximum Peak SPL: Calculated by adding the loudspeaker’s sensitivity (1W at 1m) to the peak power (dBw) of the amplifier provided.
2- Directivity Index (DI): Difference between on-axis SPL and average SPL (considering all axes) for the specified coverage range. DI= 10 log Q
3- Directivity Factor (Q): Directivity index expressed as a power ratio Q=10 exp DI/10
4- Amplifier Power: The maximum sustained power at less than 1% clipping, averaged over the intended frequency range,
5- Input Sensitivity: The sine-wave input voltage required to reach amplifier clipping, measured within the frequency range used to determine Maximum Peak SPL, with the gain on “normal” and no gain reduction
due to limiting.
6- Input Headroom/Clipping: Maximum input voltage.
7- Input Connector/Impedance: RF shunt capacitance should not reduce impedance by more than 30% at 20k Hz.