QRP Labs QLG2 Скачать руководство пользователя

Страница: 1 / 27

QLG2

GPS/GNSS

Receiver

This manual is for the QLG2 GPS/GNSS Receiver module

Firmware version

1_00.QG2, 1_00a.QG2 and 1_00b.QG2

Contents

1. Introduction....................................................................................................................................................2

2. Getting to know your QLG2............................................................................................................................2

3. Assembly.........................................................................................................................................................5

4. Firmware update procedure.........................................................................................................................20

5. Circuit diagram (schematic) and description................................................................................................23

6. Testing..........................................................................................................................................................26

7. Acknowledgments........................................................................................................................................27

8. Resources.....................................................................................................................................................27

9. Document Revision history...........................................................................................................................27

QLG2 manual for firmware 1.00a

Содержание QLG2




























Результаты поиска

Содержание QLG2

Отзывы:

Похожие инструкции для QLG2

Бренды по названию

Популярные бренды

QRP Labs QLG2, Руководство пользователя

Результаты поиска

Содержание QLG2

Отзывы:

Похожие инструкции для QLG2

Бренды по названию

Популярные бренды