background image

 QLG2-SE

GPS/GNSS

Receiver 

This manual is for the QLG2-SE GPS/GNSS Receiver module

Contents

1. Introduction....................................................................................................................................................2

2. Getting to know your QLG2-SE.......................................................................................................................2

3. Assembly.........................................................................................................................................................5

3.1 Assembly for basic operation....................................................................................................................5
3.2 Use with QCX, U3S, Clock, VFO, ProgRock etc. kits...................................................................................6
3.3 Status LEDs...............................................................................................................................................6
3.4 Fitting an ultracap (a.k.a. supercap)..........................................................................................................7
3.5 6-pin interface header..............................................................................................................................8
3.6 Interface configuration.............................................................................................................................9

4. Circuit diagram (schematic) and description..................................................................................................9

5. Testing..........................................................................................................................................................12

6. Resources.....................................................................................................................................................13

7. Document Revision history...........................................................................................................................13

QLG2-SE manual 1.00

1

Содержание QLG2-SE














Отзывы: