QRP Labs 10W HF Linear PA Скачать руководство пользователя страница 34

Страница: 34 / 34

10W HF Linear PA kit assembly

1.00

The next image shows the same thing but the vertical scale is expanded to 2dB/division:

2) Operation at full power into open output, shorted output, 20-foot long open cable, open

cable with short

– all with no oscillation or damage

3) Amplifier is still capable of 10W at 50MHz (6m band) though gain is down by 4dB compared

to HF

4) Gain is 8dB down at 70MHz (4m band) compared to HF

5) With sufficient drive, the amplifier is capable of producing 20W output at 13.8V supply using

+15dBm input, over the range 3-30MHz

6) Operated with +20V supply

7) At 10V supply still over 7W output

8) A clean 3.5MHz (80m band) source running at 10W output had 2

harmonic at -38dBc and

harmonic at -31dBc

– very good linearity

9) Operated at full-power continuous key-down, 100% duty-cycle for 1 hour, without damage

or degradation in performance.

Содержание 10W HF Linear PA



































Результаты поиска

Содержание 10W HF Linear PA

Отзывы:

Похожие инструкции для 10W HF Linear PA

Бренды по названию

Популярные бренды

QRP Labs 10W HF Linear PA, Инструкция по сборке

Результаты поиска

Содержание 10W HF Linear PA

Отзывы:

Похожие инструкции для 10W HF Linear PA

Бренды по названию

Популярные бренды