OPERATING INSTRUCTIONS
HAND TOOL FOR BLIND RIVETS UP TO Ø6,4 MM
TIOS HR64 PT
Befestigungstechnik
INSTRUCTIONS
OPENING THE BOX:
The hand tool will be standard equipped with the 6,4 mm nosepiece. The other
nosepieces are stored in the lever of the tool. A smaller set of jaws is stored in
the box, including 1 x spanner for changing the nosepiece.
FIRST USE:
Make sure before using the tool that the correct nosepiece is installed on the
tool. Otherwise change to a di erent nosepiece.
Change to a di erent nosepiece:
Close the left and right lever (1) completely. In this way the jaws and internal
spring are released. Use the spanner to unscrew the nosepiece. Replace it by
choosing the correct nosepiece for your selected blind rivets and release the
levers (1) again.
Cleaning or changing the jaws:
Close the left and right lever (1) completely. Loosen the lock nut (5) and
unscrew the front sleeve (6). Unscrew the clamping sleeve (8) to take out the
set of 3 jaws. Change or clean the jaws and re-assemble by reversing the above
procedure.
Setting a blind rivet:
Put the tool in start position by opening the levers up to maximum. There is
a clicking sound. The jaws will open completely and the ratchet mechanism
is unlocked. Insert the blind rivet into the nosepiece and slide into the hole
of the material. The hole size must be slightly larger than the rivet, check the
specification of rivet.
B
A
TECHNICAL INFORMATION
Capacity:
Standard Blind rivets 3,0/3,2 - 4,0 - 4,8/5,0 - 6,0 - 6,4 mm
Structural Blind rivets 4,8 - 6,4 mm
Material:
Aluminium, Steel and Stainless Steel
Size:
440 (L) x 180 (H) mm
Weight:
1,75 Kg
Stroke:
7,0 mm
DESCRIPTION OF THE TOOL
1. Left and right lever
2. Nosepiece 6,4 mm ID mark H
3. Mandrel collector
4. Tool Body
5. Lock Nut
6. Front sleeve
nosepieces structural rivets: M-Power
1 x 4,8 mm - ID mark J
1 x 6,4 mm - ID mark L
Read the manual
nosepieces blind rivets: standard
1 x 3,0/3,2 mm - ID mark B
1 x 4,0 mm - ID mark C
1 x 4,8/5.0mm - ID mark E
1x 6,0 mm – ID mark G
nosepieces structural rivets: P-Power
1 x 4,8 mm - ID mark K
1 x 6,4 mm - ID mark M
6
1
1
H
L
4
2
5
3
E
K
G
L
B
M
C
J
click
C
8
Manual
|
T
P
4
6
R
H
S
O
I
T
Manual
|
T
P
4
6
R
H
S
O
I
T
1
2
3
4
5
6
7
8
9
1 0
11
12
1 3
14
15
16
17
19
20
18
21
22
23
24
25
2 6
28
29
30
27
31
3 2
33
34
3 5
36
37
3 9
38
4 0
TIOS HR64 PT
2
Manual
|
T
P
4
6
R
H
S
O
I
T
Close the levers completely once to activate the ratchet mechanism. Now open de
levers for one third till you hear the clicking sound of the mechanism, then close
the levers completely.
Repeat these steps until the maximum breaking load has exceed and the mandrel
will break. Open the levers up to maximum, until the clicking sound, the ratchet
mechanism is unlocked and the rest mandrel will fall into the mandrel collector
(3). Empty the mandrel collector after setting 50 blind rivets.
Important:
after having started setting the rivet do not open the levers
completely anymore before the rivet has been set. When levers have been opened
completely before having set the rivet, the ratchet process has to be started again.
the marked items are consumables (not covered by any guarantee)
1
04P09002
12
04P00707
23
04P09003
34
04P00725
2
04A00237
13
04A00217
24
04P09005
35
04P00726
3
04P00701
14
04P00714
25
04P09007
36
04P00727
4
04P00704
15
04P00715
26
04P09008
37
04A00240
5
04P00732
16
04P00716
27
04P09010
39
04P00720
6
04P00053
17
04P00721
28
04P09011
38
04F00100
7
04P00702
18
04P00717
29
04P09012
40
04P00733
8
04P00703
19
04A00218
30
04P09013
42
04P00625
9
04A00216
20
04P00713
31
04P00722
43
04P00626
10
04P00706
21
04A00219
32
04P00723
11
04P00705
22
04P00622
33
04P00724
unlock
Manual
AS R-64-PT
Manual
AS R-64-PT
AS R-64-PT
OPERATING INSTRUCTIONS
HAND TOOL FOR BLIND RIVETS UP TO Ø6,4 MM
TIOS HR64 PT
Befestigungstechnik
INSTRUCTIONS
OPENING THE BOX:
The hand tool will be standard equipped with the 6,4 mm nosepiece. The other
nosepieces are stored in the lever of the tool. A smaller set of jaws is stored in
the box, including 1 x spanner for changing the nosepiece.
FIRST USE:
Make sure before using the tool that the correct nosepiece is installed on the
tool. Otherwise change to a di erent nosepiece.
Change to a di erent nosepiece:
Close the left and right lever (1) completely. In this way the jaws and internal
spring are released. Use the spanner to unscrew the nosepiece. Replace it by
choosing the correct nosepiece for your selected blind rivets and release the
levers (1) again.
Cleaning or changing the jaws:
Close the left and right lever (1) completely. Loosen the lock nut (5) and
unscrew the front sleeve (6). Unscrew the clamping sleeve (8) to take out the
set of 3 jaws. Change or clean the jaws and re-assemble by reversing the above
procedure.
Setting a blind rivet:
Put the tool in start position by opening the levers up to maximum. There is
a clicking sound. The jaws will open completely and the ratchet mechanism
is unlocked. Insert the blind rivet into the nosepiece and slide into the hole
of the material. The hole size must be slightly larger than the rivet, check the
specification of rivet.
B
A
TECHNICAL INFORMATION
Capacity:
Standard Blind rivets 3,0/3,2 - 4,0 - 4,8/5,0 - 6,0 - 6,4 mm
Structural Blind rivets 4,8 - 6,4 mm
Material:
Aluminium, Steel and Stainless Steel
Size:
440 (L) x 180 (H) mm
Weight:
1,75 Kg
Stroke:
7,0 mm
DESCRIPTION OF THE TOOL
1. Left and right lever
2. Nosepiece 6,4 mm ID mark H
3. Mandrel collector
4. Tool Body
5. Lock Nut
6. Front sleeve
nosepieces structural rivets: M-Power
1 x 4,8 mm - ID mark J
1 x 6,4 mm - ID mark L
Read the manual
nosepieces blind rivets: standard
1 x 3,0/3,2 mm - ID mark B
1 x 4,0 mm - ID mark C
1 x 4,8/5.0mm - ID mark E
1x 6,0 mm – ID mark G
nosepieces structural rivets: P-Power
1 x 4,8 mm - ID mark K
1 x 6,4 mm - ID mark M
6
1
1
H
L
4
2
5
3
E
K
G
L
B
M
C
J
click
C
8
Manual
|
T
P
4
6
R
H
S
O
I
T
Manual
|
T
P
4
6
R
H
S
O
I
T
1
2
3
4
5
6
7
8
9
1 0
11
12
1 3
14
15
16
17
19
20
18
21
22
23
24
25
2 6
28
29
30
27
31
3 2
33
34
3 5
36
37
3 9
38
4 0
TIOS HR64 PT
2
Manual
|
T
P
4
6
R
H
S
O
I
T
Close the levers completely once to activate the ratchet mechanism. Now open de
levers for one third till you hear the clicking sound of the mechanism, then close
the levers completely.
Repeat these steps until the maximum breaking load has exceed and the mandrel
will break. Open the levers up to maximum, until the clicking sound, the ratchet
mechanism is unlocked and the rest mandrel will fall into the mandrel collector
(3). Empty the mandrel collector after setting 50 blind rivets.
Important:
after having started setting the rivet do not open the levers
completely anymore before the rivet has been set. When levers have been opened
completely before having set the rivet, the ratchet process has to be started again.
the marked items are consumables (not covered by any guarantee)
1
04P09002
12
04P00707
23
04P09003
34
04P00725
2
04A00237
13
04A00217
24
04P09005
35
04P00726
3
04P00701
14
04P00714
25
04P09007
36
04P00727
4
04P00704
15
04P00715
26
04P09008
37
04A00240
5
04P00732
16
04P00716
27
04P09010
39
04P00720
6
04P00053
17
04P00721
28
04P09011
38
04F00100
7
04P00702
18
04P00717
29
04P09012
40
04P00733
8
04P00703
19
04A00218
30
04P09013
42
04P00625
9
04A00216
20
04P00713
31
04P00722
43
04P00626
10
04P00706
21
04A00219
32
04P00723
11
04P00705
22
04P00622
33
04P00724
unlock
Manual
AS R-64-PT
Manual
AS R-64-PT
AS R-64-PT
Einstellung des Mundstücks:
Nach der Hubeinstellung ist es wichtig das Mundstück (6) einzustellen
und mit der Kontermutter (5) zu sichern. Ö
Anschlag, Sie hören dann ein Klickgeräusch und die Mechanik ist entriegelt.
Die Blindnietmutter auf den Gewindedorn drehen bis ein Gewindegang
des Gewindedorns am Schaftende der Blindnietmutter übersteht. Dann
das Mundstück (6) bis zum Anschlag gegen den Kopf der Blindnietmutter
drehen. Mit der Kontermutter (5) sichern. Diesen Vorgang bei jedem Wechsel
der Abmessung wiederholen.
Setzen der Blindnietmutter:
Ö
g, Sie hören dann ein Klickgeräusch
und die Ratschenmechanik ist entriegelt. Die Blindnietmutter auf den
Gewindedorn des Werkzeuges drehen bis zum Anschlag an das Mundstück.
Die aufgeschraubte Blindnietmutter mit dem Werkzeug in das vorbereitete
Loch, entsprechend Vorgaben, stecken. Die Hebel nun schließen, die
Ratschenmechanik ist aktiv
rittel, Sie
hören das Klickgeräusch der Mechanik und schließen dann die Hebel ganz.
Dieser Schritt ist entsprechend der Hubzahl zu wiederholen. Anschließend
den Gewindedorn mittels des Drehknopfes (3) herausdrehen. Prüfen Sie den
festen Sitz der Blindnietmutter.
Wichtig:
Nach dem Einstellen der Nietmutter dürfen die Hebel nicht
werden, da ansonsten die
Ratschenmechanik ausgeschaltet ist. In diesem Fall wie oben beschrieben
vorgehen.
D
C
2
Handbuch
|
T
P
2
1
N
H
S
O
I
T
7
Handbuch
|
T
P
2
1
N
H
S
O
I
T
7
8
9
10
11
12
13
14
15
17
18
16
19
20
21
22
23
24
25
26
1
3
5
6
4
2
31
32
30
33
38
41
42
43
44
45
34
35
36
37
39
40
27
29
28
TIOS HN12 PT
Die markierten Positionen sind Verschleißartikel und unterliegen nicht der Gewährleistung.
1
04P00950
13
04P00715
25
04P00726
37
04P00960
2
04A00230
14
04P00716
26
04P00727
38
04P00969
3
04P00958
15
04P00721
27
04P00972
39
04P00970
4
04P00704
16
04P00717
28
04P00541
40
04P00971
5
04P00807
17
04A00218
29
04F00103
41
04A00236
6
04P00806
18
04P00713
30
04P00904
42
04A00235
7
04A00231
19
04A00219
31
04F00100
43
04A00234
8
04P00706
20
04P00816
32
04P00720
44
04A00233
9
04P00705
21
04P00722
33
04P00968
45
04A00232
10
04P00707
22
04P00723
34
04P00966
47
04P00625
11
04A00217
23
04P00724
35
04P00964
48
04P00626
12
04P00714
24
04P00725
36
04P00962
6
5
click
unlock
Cleaning or changing the jaws:
Close the left and right lever (1) completely. Loosen the lock nut (5) and
unscrew the front sleeve (6). When the lock nut is taken off, open up the levers
completely until they click. By doing this, the clamping sleeve with Jawset,
pusher, push pin spring, puller assembly and the return spring will be released
from the tool (B1). Cover the items with your hand before doing this, because
due to the force of the spring below, it can come out with some force. Now you
can unscrew the clamping sleeve and change or clean the jaws. Afterwards, re-
assemble by reversing the above procedure. For the reassembling of drawing
B1, just reassemble according to picture B1, and push it back into the tool.
B1
OPERATING INSTRUCTIONS
HAND TOOL FOR BLIND RIVETS UP TO Ø6,4 MM
TIOS HR64 PT
Befestigungstechnik
INSTRUCTIONS
OPENING THE BOX:
The hand tool will be standard equipped with the 6,4 mm nosepiece. The other
nosepieces are stored in the lever of the tool. A smaller set of jaws is stored in
the box, including 1 x spanner for changing the nosepiece.
FIRST USE:
Make sure before using the tool that the correct nosepiece is installed on the
tool. Otherwise change to a di erent nosepiece.
Change to a di erent nosepiece:
Close the left and right lever (1) completely. In this way the jaws and internal
spring are released. Use the spanner to unscrew the nosepiece. Replace it by
choosing the correct nosepiece for your selected blind rivets and release the
levers (1) again.
Cleaning or changing the jaws:
Close the left and right lever (1) completely. Loosen the lock nut (5) and
unscrew the front sleeve (6). Unscrew the clamping sleeve (8) to take out the
set of 3 jaws. Change or clean the jaws and re-assemble by reversing the above
procedure.
Setting a blind rivet:
Put the tool in start position by opening the levers up to maximum. There is
a clicking sound. The jaws will open completely and the ratchet mechanism
is unlocked. Insert the blind rivet into the nosepiece and slide into the hole
of the material. The hole size must be slightly larger than the rivet, check the
specification of rivet.
B
A
TECHNICAL INFORMATION
Capacity:
Standard Blind rivets 3,0/3,2 - 4,0 - 4,8/5,0 - 6,0 - 6,4 mm
Structural Blind rivets 4,8 - 6,4 mm
Material:
Aluminium, Steel and Stainless Steel
Size:
440 (L) x 180 (H) mm
Weight:
1,75 Kg
Stroke:
7,0 mm
DESCRIPTION OF THE TOOL
1. Left and right lever
2. Nosepiece 6,4 mm ID mark H
3. Mandrel collector
4. Tool Body
5. Lock Nut
6. Front sleeve
nosepieces structural rivets: M-Power
1 x 4,8 mm - ID mark J
1 x 6,4 mm - ID mark L
Read the manual
nosepieces blind rivets: standard
1 x 3,0/3,2 mm - ID mark B
1 x 4,0 mm - ID mark C
1 x 4,8/5.0mm - ID mark E
1x 6,0 mm – ID mark G
nosepieces structural rivets: P-Power
1 x 4,8 mm - ID mark K
1 x 6,4 mm - ID mark M
6
1
1
H
L
4
2
5
3
E
K
G
L
B
M
C
J
click
C
8
Manual
|
T
P
4
6
R
H
S
O
I
T
Manual
|
T
P
4
6
R
H
S
O
I
T
1
2
3
4
5
6
7
8
9
1 0
11
12
1 3
14
15
16
17
19
20
18
21
22
23
24
25
2 6
28
29
30
27
31
3 2
33
34
3 5
36
37
3 9
38
4 0
TIOS HR64 PT
2
Manual
|
T
P
4
6
R
H
S
O
I
T
Close the levers completely once to activate the ratchet mechanism. Now open de
levers for one third till you hear the clicking sound of the mechanism, then close
the levers completely.
Repeat these steps until the maximum breaking load has exceed and the mandrel
will break. Open the levers up to maximum, until the clicking sound, the ratchet
mechanism is unlocked and the rest mandrel will fall into the mandrel collector
(3). Empty the mandrel collector after setting 50 blind rivets.
Important:
after having started setting the rivet do not open the levers
completely anymore before the rivet has been set. When levers have been opened
completely before having set the rivet, the ratchet process has to be started again.
the marked items are consumables (not covered by any guarantee)
1
04P09002
12
04P00707
23
04P09003
34
04P00725
2
04A00237
13
04A00217
24
04P09005
35
04P00726
3
04P00701
14
04P00714
25
04P09007
36
04P00727
4
04P00704
15
04P00715
26
04P09008
37
04A00240
5
04P00732
16
04P00716
27
04P09010
39
04P00720
6
04P00053
17
04P00721
28
04P09011
38
04F00100
7
04P00702
18
04P00717
29
04P09012
40
04P00733
8
04P00703
19
04A00218
30
04P09013
42
04P00625
9
04A00216
20
04P00713
31
04P00722
43
04P00626
10
04P00706
21
04A00219
32
04P00723
11
04P00705
22
04P00622
33
04P00724
unlock
