background image

 

Thank you for choosing QNAP products! This user manual provides description of the 
hardware of the Turbo NAS and relevant guideline of certain functions. Please read carefully 
and strictly adhere to the instructions of the manual. 
 

This user manual is applicable to the following Turbo NAS models: 

TES-1885U, TES-3085U 

 

NOTE 

 

The “Turbo NAS” is hereafter referred to as “NAS”. 

 

The product you purchased may not support certain functions dedicated to specific 
models. 

 

All features, functionality, and other product specifications are subject to change 
without prior notice or obligation. 

 

Information presented is subject to change without notice. 

 

No part of this publication may be reproduced, stored in a retrieval system, or 
transmitted, in any form or by any means, mechanical, electronic, photocopying, 
recording, or otherwise, without prior written permission of QNAP Systems, Inc. 

 

QNAP and the QNAP logo are registered trademarks of QNAP Systems, Inc. Other 
products and company names mentioned herein may be the trademarks of their 
respective companies. 

 

 

Содержание TES-1885U-D1531-128GR


















































Отзывы: