```
SMH300.ppk
: obsolete file to be removed. This is the old file name permitting to store the .ppk picture to display. In this version
SMH300.PPK
has been renamed by
HUB.PPK
PF.CFG
: obsolete file to be removed. This is the old file name to enter the configuration. In this version
PF.CFG
has been renamed by
APPLI.CFG
```
☛
The SLATE106 device file system is not case sensitive, meaning that if makes not difference between lower cases and upper case.
SMH300 hub configuration file
When the SLATE106 device is paired to a
SMH300
hub, apply only your new configuration through the SMH300 hub Web configuration interface. Indeed, any direct
modification of the
APPLI.CFG
configuration file from the USB mass storage will be overwritten by the one provided by the
SMH300
hub. For further information, refer
to the
SMH300 User manual
on the Web site
Heartbeat wake-up
The default factory
SMH300
hub heartbeat wake-up configuration
- Period: every 15 minutes
- In the active interval
- 8.00 AM - 19.00 PM
- 5/7 days: Monday, Tuesday, Wednesday, Thursday, Friday
It is possible to change the heartbeat wake-up configuration. For further information, refer to the
SMH300 User manual
on the Web site
Vibration wake-up
The SLATE106 device can wake-up with a single tap. For further information, refer to the
SMH300 User manual
on the Web site
Touch key wake-up
The SLATE106 device can wake-up when the left, the middle or the right key is pressed. The vibration detection and the touch key detection must be first activated. For
further information, refer to the
SMH300 User manual
.
When a key is pressed, the associated red LED above is blinking 5 times showing that the key value is processed.
To know the location of the touch keys, refer to . With the appropriate App SignMeeting, a
Checkin
arrow and a
Checkout
arrow are drawn directly on the .ppk picture
indicating the touch sensing key placement. For further information, read the SignMeeting user manual.
Keycode sending through WPAN
The SLATE106 device has 3
Touch keys
. After a key is pressed, a keycode can be sent by the SLATE to the hub over
WPAN1
:
keycode example:
F1
,
F2
,
F3
, ... The application running on the hub can then apply some action like for example validate a meeting (
Checkin
), or free a meeting room (
Checkout
)
when the keycode is received.
Device replacement
In case you must replace a SLATE106 device which needs to be paired again to a SMH300 device:
Get the PSN of your old SLATE106 device (written on the label), note the
Index
associated to this SLATE106, and unpair it from the
SMH300
hub.
Get the
PSN
of your new SLATE106 device, (written on the label) and pair it to the SMH300 device by assigning the same
Index
. For further information, refer to
the
SMH300 User manual
on the Web site
Software release
When the SLATE106 device is paired to
SMA300 hub
, its software version is automatically released through the WPAN1 in the active interval. Once the new release is
installed, the software revision of each SLATE paired is shown in the
SMH300
hub Web configuration interface. For further information, refer to the
SMH300 User manual
on the Web site
☛
The firmware release (ex: firmware rev. = 1.10.12), able to launch the software can be set only at the factory. The firmware revision can also be seen in the shown
in the
SMH300
hub Web configuration interface.
State diagram
This is the state diagram of
Pictureframe
, configured with in
SMA300 hub
mode:
21
Содержание SLATE Series
