background image

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

11.Trouble shooting 

TROUBLE

 

 

PROBABLE CAUSES

 

 

SUGGESTED REMEDY

 

 

1. Fan will not start

 

 

A/ Fuse or circuit breaker blown. 
B/ Loose power line connections 
to the fan. 
C/ Speed controller not in correct 
position.

 

 

A/ Check main and branch circuit 
fuses or circuit breakers. 
B/ Check line wire connections to fan 

C/ Check speed controller’s position.

 

 

2. Fan sound noisy

 

 

A/ Top canopy touching ceiling. 
B/ Loose fan blade screws. 
C/ Ceiling fan not secured against 
ceiling. 
D/ Incorrect speed controller.

 

 

A/ Lower the upper Canopy from 
ceiling to 
ensure minimum 3 mm clearance. 
B/ Re-tighten all screws on fan blades 
but never over-tighten. 
C/ Re-tighten all screws in the 
hanging bracket or plate. 
D/ Change the controller to the one 
supplied.

 

 

3. Mechanical Noise

 

A/ Allow at least for 8 hours 
settling-in period.

 

 

4. Fan Wobbles

 

 

A/ Fan blades are not horizontal 
to ceiling. 
 
B/ Blade screws are loose.

 

 

A/ Measure from ceiling to tip of 
blades, then rotate fan so all blades 
are checked for equal height from 
ceiling (not adjustments may be made 
by slight pressure up or down on 
blade holders). Make sure all screws 
are securely fastened.

 

 

 

DYNAMIC BLADE BALANCE KIT 

 

YARDSTICK 

MEASURING 

P.10 

 

Содержание Cool Fan 52













Отзывы: