4 – PYLE PRO PYP-1 Stereo Control Preamplifier
Owner’s Manual
PYLE PRO PYP-1 Stereo Control Preamplifier
Owner’s Manual
- 5
Caring for your PYP-1 Stereo Control Preamplifier
This component uses a 250V 0.5A fuse for protection from
power surges and short circuits. If the unit suddenly shuts
down and will not turn on, it is likely that this fuse has
blown.
To replace the fuse:
1. Locate the fuse holder on the rear of the cabinet and
unscrew the fuse compartment cap.
2. Remove the old fuse and replace it with an identical,
serviceable fuse.
CAUTION! Never use a fuse with a higher rating!
3. Replace the fuse compartment cap.
Connecting to standard AC power
After making all other connections, set the POWER switch
to OFF position. Then connect the power cord to a standard
AC outlet.
Mounting the PYP-1
The PYP-1 is designed to accept standard rack mounting
installations. Two slots on each end of the front panel make
it suitable for such an installation.
Tightly secure four mounting screws (not supplied) through
these fours slots and into your standard electronics equipment
rack.
PYLE
PRO
Audio,
Inc.
1600
63rd
Street
Brooklyn,
NY
11204
Place
Stamp
Here
Please
complete
warranty
card,
detach
and
return
PYP-1 Specifications
Input Sensitivity/Impedance
Mic
Phono
Tape/Tuner/CD/Aux
Output Level/Impedance
Tape Rec
Pre Output
Total Harmonic Distortion
Mic
Phono
Tape/Tuner/CD/Aux
Frequency Response
S/N Ratio
Mic
Phono
Tape/Tuner/CD/Aux
Tone Control
Bass
Mid
Treble
Loudness Control
Power Requirement
Dimensions
0.5mV/600 Ohms
3.0mV/47k Ohms
150.0mV/47K Ohms
150.0mV/100k Ohms
500.0mV/47k Ohms
<0.4%
<0.04%
<0.02%
5Hz to 30k Hz (+0, -3dB)
>50dB
>70dB
>80dB
+/-12dB at 100 Hz
+/-6dB at 1k Hz
+/-12dB at 10k Hz
+4/0/+2dB at 100/1k/10k Hz
AC 110V/60 Hz or 230V/50 Hz
18
7/8
x 2
3/8
x 7
7/8
(480 x 60 x 200)
All PYLE PRO products are carefully constructed and tested before shipment.
Units purchased in the USA are warranted to be free of defects in material
and workmanship for two (2) years from the date of purchase. This warranty
is limited to the original retail purchaser of the amplifier.
Should the unit fail due to factory defects in material or workmanship, your
unit will be repaired or replaced at the sole discretion of PYLE.
To obtain warranty service, you must first call our Consumer Return Hotline
at (718) 236-6948 to obtain a Return Authorization Number. This R.A. # must
appear on the outside of your package and on all paperwork relating to your
return.
When returning the unit to us for warranty service, it must be carefully packed
and shipped, prepaid, to:
R.A.#: _____________
PYLE PRO Service Center
1600 63rd Street
Brooklyn, NY 11204
You must also include the following items with your return:
• A copy of your sales receipt or other proof of purchase
• A brief letter, indicating the problem you are experiencing with the
product
• Include in your letter your return address, daytime phone number and
R.A. number
• Also include a check or money order for $15.00 for return shipping,
handling and insurance, or provide your Visa/MC number with
expiration date.
Our obligation under this warranty is limited to the repair or replacement of
the defective unit when it is returned to us prepaid. This warranty will be
considered void if the unit was tampered with, improperly serviced or subject
to misuse, neglect or accidental damage.
Limited Warranty
