REMARK
-
MAKE SURE THE DIRECTION IS CORRECT WHEN INSERTING THE TAPE INTO THE SYSTEM.
-
THERE IS SOME SEARCHING NOISE CAN BE HEARD AND THE SYSTEM CANNOT
PERFORM NORMAL PLAYBACK FUNCTION DURING FAST FORWARD MODE.
-
THIS IS RECOMMENDED TO TAKE OUT THE CASSETTE TAPE FROM THE SYSTEM
EVERY TIMES AFTER LISTENING AND DON’T LEAVE THE CASSETTE TAPE INSIDE THE
SYSTEM WHEN NOT UNDER PLAYBACK MODE.
E-4
PHONO
NOTED:
-
REMOVE THE STYLUS PROTECTOR.
-
BE SURE THAT THE TONE ARM IS BEING DETACHED FROM THE TONE ARM
REST BEFORE OPERATING AND RE-SECURED AGAIN AFTERWARDS.
1. SELECT TO “ PHONO ” FUNCTION FROM FUNCTION SELECTOR (3)
2. SET THE SPEED SELECTOR TO THE PROPER POSITION DEPENDING ON THE RECORD TO BE PLAYED.
3. PLACE THE RECORD ON THE PLATTER (USE THE SPINDLE ADAPTOR IF REQUIRED).
4. LIFT THE TONE ARM FROM THE REST AND SLOWLY MOVE IT TO THE RECORD SIDE.
THE PLATTER WILL START TO ROTATE.
5. PLACE THE TONE ARM TO THE DESIRED POSITION OF THE RECORD.
6. ADJUST THE VOLUME TO THE DESIRED LEVEL.
7. AT THE END OF RECORD, THE PLATTER WILL AUTOMATICALLY STOP ROTATING. LIFT
THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST.
8. TO STOP MANUALLY, LIFT THE TONE ARM FROM THE RECORD AND RETURN IT TO THE REST.
REMARK
: AS SOME KIND OF RECORD THE AUTO-STOP AREA WAS OUT OF THE UNIT SETTING, SO IT WILL
STOP BEFORE THE LAST RACK FINISH. IN THIS CASE, SELECT THE AUTO-STOP SWITCH (29) TO “ OFF
“ POSITION, THEN IT WILL RUN TO THE END OF THE RECORD BUT WILL NOT STOP AUTOMATICALLY (TURN
OFF THE UNIT BY POWER BUTTON OR SWITCH BACK THE AUTO-STOP SWITCH TO “ ON “ POSITION TO
STOP THE PLATTER ROTATE). THEN PUT BACK THE TONE ARM TO THE REST POSITION.
LINE OUT CONNECTION
YOU CAN CONNECT THE SYSTEM TO YOUR WHOLE HI-FI SYSTEM BY CONNECTING THE LINE OUT SOCKET
(28) TO THE AUXILIARY INPUT SOCKET WITH A RCA CABLE (NOT INCLUDED).
ENCODING OF CD DISC / PHONO OR CASSETTE TAPE INTO MP3 FILE
THE SYSTEM IS ABLE TO ENCODE CD, RECORD (FROM PHONO) AND CASSETTE DECK FILE (FROM TAPE)
TO MP3 FORMAT AND RECORDING AT MEMORY MEDIA WITH USB CONNECTING PORT OR SD/MMC CARD.
A) CD ENCODING
I) RECORDING 1 TRACK
1.
PLUG IN THE USB PEN DRIVE FOR RECORDING (MAKE SURE IT AHD ENOUGH EMPTY SPACE).
2.
PLAY THE CD TRACK YOU WANT TO ENCODE/RECORD, AS NORMAL.
3.
PRESS THE “ RECORD “ BUTTON (9) DURING PLAYBACK OF THE DESIRED TRACK
4. “
“ & “
“ WILL BE FLASHING ON THE LCD DISPLAY (2) TO SHOW ENCODING IS IN
PROGRESS.
5.
AFTER THE ENCODING PROCESS HAS FINISHED, THE UNIT WILL STOP PLAYBACK AUTOMATICALLY.
II) RECORDING THE COMPLETE CD
1.
PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE CD TRAY & THEN CLOSE THE CD DOOR.
2.
AFTER DISC SEARCH HAS BEEN COMPLETED, PRESS THE “ RECORD “ BUTTON (9) –
NOTE:
DO NOT PRESS “ PLAY/PAUSE/STOP ” BUTTON (19) AND THEN "RECORD" BUTTON, OR ONLY THE
SELECTED TRACK WILL BE RECORDED.
3. “
“ & “
“ WILL BE FLASHING ON THE LCD DISPLAY (2) TO SHOW ENCODING IS IN
PROGRESS.
4.
AFTER THE ENCODING PROCESS HAS FINISHED, THE UNIT WILL STOP PLAYBACK AUTOMATICALLY.
III) ENCODING BY PROGRAM
1. PLACE A CD WITH THE PRINTED SIDE FACING UP INSIDE THE TRAY & THEN CLOSE THE CO DOOR
2.
SELECT THE DESIRE TRACKS BY FOLLOWING “
CD/MP3 DISC PROGRAMMING
“ PROCEDURES.
THEN PRESS “ PLAY/PAUSE/STOP “ BUTTON (19) TO START PLAYBACK.
