manualshive.com logo in svg

PVA JDX, Руководство пользователя

Поделиться
Скачать
PVA JDX Скачать руководство пользователя страница 28

JDX  PVA  

 

 

 

Revision H  (2016)

 

28 of 39

 

 

 

Jet and Fluid Pressure 

6.1

The PVA JDX Jet Valve controller has integrated air regulators (7, 10) which control the 
pressure to the Jet and the Fluid supply. Two digital gages (2, 6) show the pressure 
levels. The Fluid Pressure can be turned off with the air switch (11).  

The jet requires a minimum of 35psi to function correctly. In general, 45psi is a good 

starting point for jet pressure. If the jet does not break off cleanly, increase the jet 

pressure. If you increase the jet pressure to 65psi and still have accumulation, increase 

the material temperature.  

 

 

Temperature Controller 

6.2

The main menu of the temperature controller shows the current temperature (PV) on 

the top line, and the set point temperature (SV) on the bottom line of the display. 

 

Figure 33: Temp Control 

 

To change the SV temperature 

6.2.1

1.

 

Use the UP/DOWN arrows to increase or decrease the temperature.  

2.

 

Press the ENTER key to save the change. 

 

Figure 34: To Change the SV Temperature 

  
 

 

Set Point Temperature 

Enter Key 

Current Temperature 

Index Key 

Содержание JDX








































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды