PureTools PT-C-HDCEC Скачать руководство пользователя страница 21

Страница: 21 / 28

User Manual

PT-C-HDCEC

Command

Function

Feedback Example

RS232U/-[X]:XXX

Set the user-defined HEX command to
send to the third-party device (e.g.
projector) whose baud rate is X.

RS232USER/-3:30 31 32

Send the user-defined command
“30 31 32” to the third-party
whose baud rate is 9600.

RS232DLY:[XXX].

Set the sending interval time between
RS232 ON and RS232 USER to XXX
(default 3s, range of 1S to 180s).

SET RS232 ON DELAY TIME [XXX]S

RS232PCS[X].

Set the sending number of RS232 OFF to
X.

Description

1 time

2 times

SET SEND RS232 OFF ONE TIME!

RS232OFFDLY:[XX].

Set the two times sending interval time
of RS232 OFF to XX (default 2s, range of
1S to 10s).

SET RS232 OFF SEND DELAY TIME
[XXX]S

GRS232DLY.

Report the sending interval time
between RS232 ON and RS232 USER.

SET RS232 ON DELAY TIME 3S

GRS232PCS.

Report the sending number of RS232
OFF

SELECT SEND RS232 OFF ONE
TIME!

GRS232OFFINT.

Report the two times sending interval
time of RS232 OFF.

SET RS232 OFF SEND DELAY TIME
2S

6.1.5

IR Control Setting

Command

Function

Feedback Example

IRSTUDY[X].

Learns the IR command from IR remote.

Description

STUDY IR DISPLAY OFF

STUDY IR DISPLAY ON

STUDY IR USER

IRSTUDY0.

READY STUDY IR DISPLAY
OFF,PLEASE REMOTE CONTROL
RECEIVER IN 10S!

Содержание PT-C-HDCEC




























Результаты поиска

Содержание PT-C-HDCEC

Отзывы:

Похожие инструкции для PT-C-HDCEC

Бренды по названию

Популярные бренды

PureTools PT-C-HDCEC, Руководство пользователя

Результаты поиска

Содержание PT-C-HDCEC

Отзывы:

Похожие инструкции для PT-C-HDCEC

Бренды по названию

Популярные бренды