-04-
4. OPERATION
A. Installation
1.
Make sure your input AC voltage is compliant to the adapter specifications.
2. Only use the power adapters provided with the CSW300. If you use your own adapter, make sure
the power output is 5V DC, 1A.
3. In a direct line-of-sight, the maximum range of A/V signal transmission can reach up to about
100 meters. This distance can be shortened by obstacles or walls placed between transmitter and
receiver. The optimum indoor range is under 100m.
4. To ensure a good infrared remote control operation, aim your remote control* at the IR receiver of
the CSW300 and press the buttons firmly. For some remote controls it may be necessary to press
and hold each button for about a second. The working angle of the IR receiver is +/- 15°.
5. The remote controller has to be used within the distance of 0.3m - 5m at a working angle of
+/- 15°.
* The max. transmission distance (100m) is reliant on optimum conditions. Other devices in the
vicinity using the 5GHz band (WiFi networks or other wireless video transmitters) can lead to inter-
ference and a significant decrease of the transmission distance or picture stability.
B. Transmitter & Receiver Pairing MODE
1. First press the “MODE” button on the receiver‘s box.
2. You will see a message “Connecting through Pairing ... ” on screen.
3. Then press the “MODE” button on the transmitter‘s box.
4. Connection will be auto-established after once successfully paired.Wait for a few seconds for auto
connection.
C. IR Extending Function
1. Make sure the IR emitter has been installed properly on the transmitter‘s box.
2. Make sure the IR receiver has been installed properly on the receiver‘s box.
3. Use the remote control of your source device to control the source form the receiver‘s box.
NOTE: Please do not cover CSW300 transmitter and receiver with any object! Those objects can
block the air circulation and cause serious defects and injuries. The warranty will also be void.
5. LED INDICATION
There are LEDs and a UI for indication of system operation. For more detail, please check the table
below:
Condition
TX
RX
RX UI(TV Screen)
Power on
Solid RED
Solid RED
Startup image
Mode
(Press the button)
RED Flashing
Solid Blue
Connection through pairing
No connection
Blue Flashing
Solid Blue
Scanning
Connection & Play Solid Blue
Solid Blue
Video
6. FREQUENTLY ASKED QUESTIONS
1. When there is no picture presented:
Make sure the direct connection from the source device to the sink device works properly. Check,
if all connectors are connected well; check if all cables can support the transmission speed. High
Speed HDMI cables from PureLink are recommended. Unplug the power cable to restart CSW300.
2. When there is no sound:
First, try to adjust the volume of the connected sink device (TV). Check cable connection to see
if it works properly. Check cable to see if it supports video transmission only (DVI) or not. The
HDCP encryption may not match very well at first connection; please unplug the power cable to
restart CSW300.
3. When there is no 3D effect (Only for 3D hardware):
Make sure the 3D function of the 3D sink device is activated (set to AUTO or 3D ON). Make sure
the 3D function of the 3D source device is activated (set to AUTO or 3D ON). Make sure that the
power of the shutter glasses (if active 3D) is on. Check the power of CSW300. Make sure, you use
the right glasses for the 3D technology in use (active or passive).
4. If the image is unstable or a snowing image shows on screen:
You might get interference form other wireless devices or heavy voltage sources inside the room
(ex. WiFi Router, Microwave, air conditioner). Please keep CSW300 away from those sources of
interference. The wireless transmission distance may be too far or blocked by a wall or another
object. Please place CSW300 in another location where you can get good signal and video
quality. Please change the direction of transmitter and receiver to get a better connection.
-05-
ENGLISH
