PULSION PC8500 Скачать руководство пользователя

Страница: 70 / 105

Installation and setup

Page C-44

Operator’s Manual PiCCO

Version 3.1

6.1

Alarms

Alarms are displayed with priority 1, error messages with lower priority are overridden.

Alarm

Cause

Remedy

High PCCO / PCCI

PCCO / PCCI > alarm limit

Low PCCO / PCCI

PCCO / PCCI < alarm limit

High ScvO

ScvO

> alarm limit

Low ScvO

ScvO

< alarm limit

High SpO

SpO

> alarm limit

Low SpO

SpO

< alarm limit

Low Battery

Battery status < 25% and
device is not connected to
mains power

Connect device to mains power

Internal error -
restart the device or
SERVICE

No signals longer than 10 s
(e.g. internal USB does not
work)

Restart the device, if error exists
further on, SERVICE necessary

Internal error -
SERVICE necessary

Internal error

SERVICE necessary

6.2

Error Messages

Text error messages are displayed in the information bar (chapter C4.1). When viewing old measurements the
respective error messages are displayed as well.

General

Error Message

Cause

Remedy

Enter patient data for
indexed values

Patient data (height / weight) etc. not
entered

Enter patient data.

Thermodilution

Error Message

Cause

Remedy

Invalid / Faulty catheter - Change
catheter

Faulty catheter, not
compatible or not connected

Connect compatible
catheter

Unknown catheter - Enter ACC

Unknown catheter type with
unknown resistor

Enter ACC in
corresponding field

Injection Error - Repeat injection,
rapid and smooth

Injection not smooth

Repeat injection rapidly
and smoothly

Injectate Temp. Sensor Error -
Check sensor cable and sensor
housing

Defective injectate temp.
sensor or sensor cable

Check and replace if
necessary

Содержание PC8500










































































































Результаты поиска

Содержание PC8500

Отзывы:

Похожие инструкции для PC8500

Бренды по названию

Популярные бренды

PULSION PC8500, Руководство оператора и информация о продукте

Результаты поиска

Содержание PC8500

Отзывы:

Похожие инструкции для PC8500

Бренды по названию

Популярные бренды