www.pulsar.pl
PSBEN5012C/LCD
28
The main panel of the program has been formulated in such a way that it is possible to divide it into smaller
areas, depending on the number of power supplies.
The program enables both a visualisation and an analysis of the received data. Exceeding of the acceptable
parameters is indicated by highlighting in red the appropriate area or by twinkling of the indicator. Particular tabs
contain a chart with an overview of the PSU parameters and failure memo along with the information about status
and the electrical specifications of the technical outputs.
The ”Power Security” program is available on our website:
www.pulsar.pl
Its detailed description can be found in the manual of the program.
6. Technical specifications.
Electrical specifications (tab.10).
Mechanical specifications (tab.11).
Operation safety (tab.12).
Operating specifications (tab.13).
Factory settings (tab. 14).
Table 10. Electrical specifications.
PSU type
A, protection grade 1÷3, II environmental class
Mains supply
230V/AC (-15%/+10%)
Current consumption
0,6 A
Power frequency
50Hz
PSU’s power
78 W
Efficiency
70%
Output voltage
11,0V÷13,8 V DC – buffer operation
10,0V÷13,8 V DC – battery-assisted operation
Output current
- for grades 1, 2:
Io = 1,4A + 3A battery charge
- for grade 3:
Io = 0,56A + 3A battery charge - (connection with ARC
required, compliant with 9.2 – PN-EN 50131-1)
Io = 0,28A + 3A battery charge
- for general use:
Io =5A
(without bartery)
Io =4,4A + 0,6A battery charge
Io = 3,5A + 1,5A battery charge
Io = 2,8A + 2,2A battery charge
Io = 2A + 3A battery charge
Output voltage setting, escalation and keeping
time
5ms / 40ms / 18ms
Output voltage adjustment range
12 V÷ 14,5 V
Ripple voltage
30 mV p-p max.
Current consumption by the PSU systems
during batter-assisted operation
I = 26mA
I = 17 mA – highlighting of the LCD desktop is off
Battery charging current
0,6A/ 1,5A/ 2,2A/ 3A –I
BAT
jumper selectable
Low battery voltage indication
Ubat < 11,5V, during battery-assisted operation
Over voltage protection OVP
U>15,5V, disconnection of the output voltage, automatic return
(AUX+ disconnection)
Short circuit protection SCP
200% ÷ 250% of the PSU power - current limiting and/or fuse
fault in the battery circuit (fuse-element replacement required)
Overload protection OLP
Program - equipment
Battery circuit protection SCP and reverse
polarity connection
T6,3 A- current limiting, F
BAT
fuse (failure requires fuse-element
replacement)
Deep discharge battery protection UVP
U<10,0 V (± 2%) – disconnection (-BAT) of the battery,
adjustment from the
LCD desktop’s level
- type – electronic, max 50mA/30V DC, galvanic isolation
1500V
RMS
- time lag, approx. 5s/140s/17m/2h 20m (+/-5%)
- type – electronic, max 50mA/30V DC, galvanic isolation
1500V
RMS
- type – electronic, max 50mA/30V DC, galvanic isolation
1500V
RMS
Technical outputs:
- EPS FLT; output indicating AC power failure
- APS FLT; output indicating battery failure
- PSU FLT; output indicating PSU failure
- TAMPER output indicating enclosure opening
and
detachment
from the mounting surface
- microswitches x2, NC contacts (enclosure closed and fixed to
the mounting surface)
, 0,5A@50V DC (max.)
