INSRWF0314
SY
ST
ÈM
E
Q
U
AL
IT
É
CE
RT
IFIÉ
- REGISTERE
D Q
UA
LIT
Y S
YS
TE
M
This unit
complies with
the CSA
standards
USER’S gUidE
RWF SERiES
WAll fAn heATer
replACemenT ComponenT liST inCluded
For further information or to consult this guide online, please visit our website at
www.stelpro.com
Before installing and operating this product, the user and/or installer must read, understand and follow these instructions and keep them handy for future refer-
ence. If these instructions are not followed, the warranty will be considered null and void and the manufacturer deems no further responsibility for this product.
This product must be installed by a qualified person and connected by a
certified electrician
, according to the
electrical and building codes
effective in your region.
The following instructions must be adhered to in order to avoid personal injuries or property damages, serious injuries and potentially fatal electric shocks.
Protect the heating unit with the appropriate circuit breaker or fuse, in accordance with the nameplate.
Make sure the line voltage (volt) is consistent with that indicated on the unit’s nameplate.
This unit must be
grounded
.
Switch off the power at the circuit breaker/fuse before installing, repairing and cleaning the unit.
Make sure the unit is appropriate for the intended use (if needed, refer to the product catalog or a representative).
Recommended heating capacity:
1,25 W/cubic foot (0.03 m³).
It corresponds to
10 W/square foot (0.09 m²)
based on a standard ceiling height of 8 feet (2.44 m). The recommended capacity is usually sufficient
for normal heating needs. Please note that the insulation quality of walls and windows are some of the factors that influence heat losses, which modify the
required capacity to heat a room. If needed, refer to a specialist who will be able to calculate these heat losses and optimize the required capacity or consult
the “Online heating calculation” section of the Stelpro Design Web site (residential buildings). To heat a large room and increase your comfort, it is recom-
mended to install several units instead of one. For example, 2 X 1000 W rather than 1 X 2000 W.
WaRning
HISTORIQUE DES RÉVISIONS | REVISIONS HISTORY
REV.
DATE
DESCRIPTION
MODIFIÉ PAR | MODIFIED BY:
MATÉRIEL | MATERIAL :
1 / 1
# PIÈCE | PART # :
RWF
FEUILLE | SHEET :
A
X:\01_PRODUITS\FAMILLES\RWF\DOCUMENTATION\RWF_ISO.dft
TROISIÈME ANGLE DE
PROJECTION
THIRD ANGLE PROJECTION
FORMAT | SIZE :
DESCRIPTION :
AÉROCONVECTEUR MURAL
EMPLACEMENT:
TOLÉRANCES SI NON-SPÉCIFIÉES | TOLERANCES IF NOT SPECIFIED
ANGULAIRE
|
ANGULAR:
±.03"
±.015"
.XX
.XXX
=
=
[ ±.76mm ]
[ ±.38mm ]
±1°
±0.5°
XX°
XX.X°
=
=
lboujida
2005-12-01
2013-09-24 / bcloutier
LINÉAIRE
|
LINEAR:
CRÉÉ LE | CREATED ON :
CRÉÉ PAR | CREATED BY :
MIS À JOUR | UPDATED :
L'INFORMATION CONTENUE DANS CE
DOCUMENT EST LA pROpRIÉTÉ DE
STELpRO DESIGN. EN AUCUN CAS,
L'INFORMATION NE pEUT ÊTRE
UTILISÉE, SAUF SOUS AUTORISATION
ÉCRITE DE STELpRO DESIGN.
THE INFORMATION IN THIS DOCUMENT
IS THE pROpERTY OF STELpRO DESIGN.
IN ANY CASE, THE INFORMATION CAN'T
BE USED, EXCEpT BY THE WRITTEN
CONSENT OF STELpRO DESIGN.
