PIM90.241
Feb. 2022 / Rev. 2.0 DS-PIM90.241-EN
www.pulspower.com
12 / 17
All parameters are specified at 24V, 3.8A, 230Vac, 25°C ambient and after a 5 minutes run-in time unless otherwise noted.
14. EMC
The EMC behavior of the device is designed for applications in industrial environment as well as in residential, commercial
and light industry environments.
The device complies with EN 61000-6-1, EN 61000-6-2, EN 61000-6-3, EN 61000-6-4, EN 61000-3-2 and EN 61000-3-3. The
device complies with FCC Part 15 rules. Operation is subjected to following two conditions: (1) this device may not cause
harmful interference, and (2) this device must accept any interference received, including interference that may cause
undesired operation.
Do not use this device on AC 100V mains with more than 2.9A load when the application is sensitive to short output voltage
dips during mains interruptions even with a length shorter than 20ms.
EMC Immunity
Electrostatic discharge
EN 61000-4-2
Contact discharge
8kV
Criterion A
Air discharge
8kV
Criterion A
Electromagnetic RF field
EN 61000-4-3
80MHz - 6GHz
10V/m
Criterion A
Fast transients (Burst)
EN 61000-4-4
Input lines
4kV
Criterion A
Output lines
2kV
Criterion A
Surge voltage on input
EN 61000-4-5
L
→
N
2kV
Criterion A
N / L
→
Earthed output
4kV
Criterion A
Surge voltage on output
EN 61000-4-5
(+)
→
(−)
1kV
Criterion A
(+)
→
(−) Earthed
1kV
Criterion A
(−)
→
(+) Earthed
1kV
Criterion A
Conducted disturbance
EN 61000-4-6
0.15 - 80MHz
10V
Criterion A
Voltage dips
EN 61000-4-11
0% of 100Vac
0Vac, 20ms
Criterion A/C
40% of 100Vac
40Vac, 200ms
Criterion C
70% of 100Vac
70Vac, 500ms
Criterion A
0% of 120Vac
0Vac, 20ms
Criterion A
40% of 120Vac
48Vac, 200ms
Criterion C
70% of 120Vac
84Vac, 500ms
Criterion A
0% of 200Vac
0Vac, 20ms
Criterion A
40% of 200Vac
80Vac, 200ms
Criterion A
70% of 200Vac
140Vac, 500ms
Criterion A
Voltage interruptions
EN 61000-4-11
0V
5000ms
Criterion C
Powerful transients
VDE 0160
Over entire load range
750V, 1.3ms
Criterion A
Performance criterions:
A:
The device shows normal operation behavior within the defined limits.
B:
The device operates continuously during and after the test. During the test minor temporary impairments may
occur, which will be corrected by the device itself.
C:
Temporary loss of function is possible. The device may shut-down and restarts by itself. No damage or hazards
for the device will occur.
A/C: Criterion A for output current below 2.9A and criterion C for output currents above 2.9A.
EMC Emission
Conducted emission input lines
EN 55011, EN 55032, FCC Part 15, CISPR 11,
CISPR32
Class B
Conducted emission output lines
IEC/CISPR 16-1-2, IEC/CISPR 16-2-1
Limits for local DC power networks
fulfilled.
Radiated emission
EN 55011, EN 55032, CISPR 11, CISPR 32
Class B
Harmonic input current
EN 61000-3-2
Fulfilled (Class A)
Voltage fluctuations, flicker
EN 61000-3-3
Fulfilled, tested with non pulsing
constant current loads.
Switching Frequencies
Main converter
5kHz to 120kHz
Input voltage and output load
dependent
