IMPORTANT SAFETY INSTRUCTIONS
To reduce the risks associated with the use of abrasive products, disc pads, tool breakup, sharp
edges, hazardous pressure, rupture, vibration and noise:
•
Read, understand and follow the safety information contained in these instructions prior to using
this tool. Keep these instructions for further reference.
•
Only properly trained personnel should service this tool. Any other service will void warranty.
• Practice safety requirements - work alert, have proper attire, and do not operate tools under the
influence of alcohol or drugs.
• Operators and nearby personnel must always wear protection for eyes, ears, and respiratory
protection when in the work area or while operating this product. Follow your employer’s safety
policy for PPE’s and/or ANSI Z87.1 or local/national standards for eye wear and other personal
protective equipment requirements.
• Never exceed marked maximum input pressure (90psi / .62Mpa / 6.2Bars).
• Proper eye protection must be worn at all times.
• Tool shall not be operated in the presence of bystanders.
• If you notice any abnormal noise or vibration when operating the product, immediately discontinue
its use and inspect for worn or damaged components (mounting hardware, abrasive product, etc).
Correct or replace the problem component. If the problem persists, return the tool to PTA Canada
for repair or replacement. Please refer to warranty instructions.
• Never operate this tool without all safety features in place and in proper working order.
• Do not remove or disable safety feature of on-off control device.
• Make sure the tool is disconnected from its air source before servicing, inspecting, maintaining,
cleaning, and before changing abrasive product.
• Prior to use, inspect abrasive product, disc pad, and other accessories for possible damage. If
damaged, replace with new abrasive product and accessories available from PTA Canada.
• Never over-ride the safety start-stop control such that it is in the on position.
• Use only with mounting hardware recommended by PTA Canada; check with PTA Canada for
mounting hardware requirements.
• Always ensure that shaft diameters match internal diameters of the collet inserts.
• Maximum operating speed of abrasive products or accessories must be reduced whenever the
exposed length of shaft (overhang) is longer than corresponding PTA Canada approved products.
• Use only with abrasive products not requiring guards according to local, state and federal
regulations.
WARNING
www.premiumtool.com
PTA Canada 10761 - 181 ST NW Edmonton, AB, Canada T5S 1N3
RISKS
PREVENTION
Vibration
• If any physical discomfort is experienced, work should be stopped
promptly to seek medical attention. Injury may result from repetitive work,
motion and exposure to excessive vibration.
Loud Noise
• Always wear protection for eyes, ears, and respiratory protection while
operating this product. Follow your employer’s safety policy for PPE’s and/
or ANSI Z87.1 or local/national standards for eyewear and other personal
protective equipment requirements..
Fire or Explosion
• Do not operate the tool in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. The abrasives are able
to create sparks when working material, resulting in the ignition of the
flammable dust or fumes.
Dust Ingestions or
Eye/Skin Exposure
• Use appropriate respiratory and skin protection, or local exhaust as
stated in the MSDS of the material being worked on.
Hazardous Voltage
• Do not allow this tool to come into contact with electrical power sources
as the tool is not insulated against electrical shock.
Skin Abrasion/Burns/
Cuts/Entrapment
• Keep hands, hair, and clothing away from the rotating part of the tool.
• Wear suitable protective gloves while operating tool.
• Do not touch the rotating parts during operation for any reason.
• Do not force tool or use excessive force when using tool.
Fly Off of Abrasive
Product or Parts
• Use care in attaching abrasive product, disc pad, and mounting hardware;
following the instructions to ensure that they are securely attached to the
tool before use.
Hazardous Pressure
Rupture
• Be aware that incorrectly installed hoses and fittings might unexpectedly
come loose at any time and create a whipping/impact hazard.
