PT AMC131 Скачать руководство пользователя

Страница: 57 / 108

Device Locator Record

The MMC firmware supports the

Get Device Locator Record ID

command for FRU device #0

(the only FRU device represented by an MMC). The MMC firmware obtains the ID of the IPMB
management controller device locator record by scanning the SDR records embedded into the
firmware.

Table 5-2

shows an example of an IPMB management controller device locator record (SDR

type 0x12) describing the properties of the MMC:

Table 5-2:

IPMB Management Controller Device Locator Record

Parameter

Value

Power State Notification

ACPI System Power State notification required

ACPI Device Power State notification required

Global Initialization

Controller logs Initialization Agent errors

Log Initialization Agent errors accessing this
controller

Event Generation

Enable event message generation from controller

Device Capabilities

Chassis Device

Bridge

IPMB Event Generator

YES

IPMB Event Receiver

FRU Inventory Device

YES

SEL Device

SDR Repository Device

Sensor Device

YES

FRU Entity ID

0xC1

Entity Instance

(slot dependent)

OEM-specific

Device ID String Type/Length

8-bit ASCII with size of Device ID String (see below)

Device ID String

AMC131

Содержание AMC131













































































































Результаты поиска

Содержание AMC131

Отзывы:

Похожие инструкции для AMC131

Бренды по названию

Популярные бренды

PT AMC131, Руководство по оборудованию

Результаты поиска

Содержание AMC131

Отзывы:

Похожие инструкции для AMC131

Бренды по названию

Популярные бренды