PT AMC131 Скачать руководство пользователя страница 46 | Manualshive

Страница: 46 / 108

background image

Chapter 4: Connectors

46

Console Cable

A console cable is available to provide a male DB-9 connector. The cable provides a DTE
connection (RS-232 levels), allowing connection to a modem (DCE) without the need of a null
modem. A null modem (DB-9F to DB-9F) is provided to allow connection to a terminal or PC
(DTE) directly. This cable is 3 feet in length (min.). The pinout of the DB-9 is described in

.

10/100/1000 Base-T Ethernet Port Connectors (J3, J4)

Four Ethernet ports are supported by the AMC131. Two ports are implemented as 10/100/1000
BASE-T/TX connections to front panel RJ-45 connectors (FP1 and FP2), in order to support
CAT5 cabling. These connectors are pinned for medium dependent interface (MDI) operation
on DTE equipment according to IEEE 802.3- 2000, Table 23-6.

Both front panel Ethernet ports can be utilized as management ports to the MPC8641D
processor. During the boot process, you are provided with a time period to choose to abort the
normal process and proceed with a boot loading process using an Ethernet management port.

shows the 10/100/1000 Base-T Ethernet port pinout.

Table 4-4:

DB-9 Console Cable Pinout

DB-9

I/O

1

NC

2

RXD

3

TXD

4

DTR Looped to Pin 6

5

GND

6

DSR Looped to Pin 4

7

RTS Looped to Pin 8

8

CTS Looped to Pin 7

9

NC

Table 4-5:

10/100/1000 Base-T Ethernet Port Connector Pinout (RJ-45)

RJ-45 Pin

Name

1

TX_D1+

2

TX_D1-

3

RX_D2+

4

BI_D3+

5

BI_D3-

6

RX_D2-

7

BI_D4+

8

BI_D4-

«
...
44
45
46
47
48
...
»

Содержание AMC131













































































































Отзывы:

Нет отзывов

Похожие инструкции для AMC131

BaByBjörn Baby Carrier Active

Бренд: BabyBjorn Страницы: 5

ROVER 3 Bassinet

Бренд: Babybee Страницы: 12

Бренд: Najell Страницы: 16

Бренд: Moby Страницы: 27

Бренд: CYBEX Страницы: 50

Бренд: CYBEX Страницы: 76

Бренд: Miamily Страницы: 12

HIPSTER ESSENTIAL

Бренд: Miamily Страницы: 16

Бренд: manduca Страницы: 20

BaByBjörn Baby Carrier Origina

Бренд: BabyBjorn Страницы: 5

Бренд: babylonia Страницы: 25

Breathable Baby Ring Sling

Бренд: Sukkiri Страницы: 10

Бренд: Kiddcare Страницы: 4

Бренд: Close Parent Страницы: 9

Бренд: Close Parent Страницы: 16

Caboo +cotton blend

Бренд: Close Страницы: 58

Бренд: Graco Страницы: 28

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды