PT AMC131 Скачать руководство пользователя | Manualshive

Страница: 28 / 108

background image

Chapter 2: Introduction

28

Module Management Controller (MMC)

The AMC131 includes a Module Management Controller (MMC) based on the Atmel
ATMEGA128L-8MU, which interfaces to the local Intelligent Platform Management bus (IPMB-
L). The MMC monitors and controls the module's payload per the PICMG AMC.0 specification.

Chapter 5, “System Monitoring and Alarms,” on page 53

for more information on MMC

functionality, supported commands, AMC131 sensors, and the firmware upgrade process.

The AMC131 is compliant with standard

Intelligent Platform Management Interface v1.5

Specification

functionality. See

“Module Management Controller,” on page 107

, for information

about this specification.

Sensors

The following sensors are monitored on the AMC131:

•

Air intake temperature sensor

•

MPC8641D built in temperature sensor

•

MMC voltage monitoring (3.3V management power and 12V power to the AMC slot)

•

MMC hot-swap switch sensor

For more information on AMC131 sensors,

Chapter 5, “System Monitoring and Alarms,” on

Universal Serial Bus

The AMC131 has one Universal Serial Bus (USB) port on the front panel (see

“AMC131 Front Panel,” on page 23

). This USB 2.0 port is supported by the Philips ISP1160

dual-port host controller.

For USB pinout information, see

“Console Port Connector (J2),” on page 45

Console Port

The front panel console port (see

Figure 2-1, “AMC131 Front Panel,” on page 23

) is an RJ-11

connector with RS-232 signal levels and 15 KV ESD protection. This port is pinned out for Data
Terminal Equipment (DTE) operation. Request-to-send (RTS), clear-to-send (CTS) and
modem-control signals are not supported.

There are two options for connectivity through this connector

•

Module Management Controller

•

Payload module

Although two Universal Asynchronous Receiver/Transmitter (UARTS) are provided on the
MPC8641D, only Port 0 is connected to the transceiver. Port 1 is used as a host interface for
communication to/from the MMC.

When enabled (via

), the user can toggle between the processor and the MMC

console ports with a single break character. A double break (break-break), when enabled (via
register 8), causes a hard reset to the processor.

«
...
26
27
28
29
30
...
»

Содержание AMC131













































































































Отзывы:

Нет отзывов

Похожие инструкции для AMC131

SIMMONS KIDS 25403

Бренд: Delta Children Страницы: 13

COMe Ref. Carrier-i T6 TMIE

Бренд: Kontron Страницы: 30

COMe Ref. Carrier-i T6 TMIP

Бренд: Kontron Страницы: 35

Бренд: Kontron Страницы: 100

Бренд: Bebe by Me Страницы: 2

Бренд: Go-Go Babyz Страницы: 14

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды