PT AMC123 Скачать руководство пользователя страница 83

Страница: 83 / 104

Front Panel Connectors

The AMC123 contains the following connectors on the front panel. See

for connector locations.

Ethernet Connectors (J1, J2)

Two RJ45 connectors on the AMC123's front panel provide two 1 Gigabit Ethernet channels.
Two bicolor LEDs are located inside each RJ45 connector:

•

Front Panel ENET Link

•

Front Panel ENET Activity

See

“LED Indicators,” on page 31

, for more information about these LEDs and

Table 5-3,

“Ethernet Connectors Pinout,”

for pin definitions.

Caution:

Insert only RJ45 plugs into the Ethernet connector. Other connectors may damage the
Ethernet connector pins.

USB Connector (J3)

A 4-pin, standard Type A USB 2.0 Port 0 Interface connector is available on the AMC123's front
panel.

Table 5-4, “USB Connector Pinout,”

shows pin definitions for this connector.

Table 5-3:

Ethernet Connectors Pinout

Pin

Signal Name

BI_DA+

BI_DA-

BI_DB+

BI_DC+

BI_DC-

BI_DB-

BI_DD+

BI_DD-

Table 5-4:

USB Connector Pinout

Pin

Signal Name

VCC (+5V)

USB_N

USB_P

GND

Содержание AMC123









































































































Результаты поиска

Содержание AMC123

Отзывы:

Похожие инструкции для AMC123

Бренды по названию

Популярные бренды

PT AMC123, Руководство пользователя

Результаты поиска

Содержание AMC123

Отзывы:

Похожие инструкции для AMC123

Бренды по названию

Популярные бренды