PT AMC123 Скачать руководство пользователя страница 66

Страница: 66 / 104

Chapter 4: System Monitoring and Alarms

Debug/Verbosity Level

The SIPL provides commands to enable and disable output of error/diagnostic messages to the
serial debug interface at runtime:

•

“Get Debug Level Command,” on page 66

•

“Set Debug Level Command,” on page 66

Get Debug Level Command

To get the current debug level, the

Get Debug Level

command must be used. This command

has the following synopsis:

[B8 xx 03 0A 40 00]

The MMC responds to the

Get Debug Level

command with the following reply:

[BC xx 03 00 0A 40 00

<debug level>

]

The

parameter contains the bit fields shown in

Table 4-9, “MMC Debug

Levels,”

below.

Set Debug Level Command

To change the current debug level, the

Set Debug Level

command must be used. This

command has the following synopsis:

[B8 xx 04 0A 40 00

<debug level>

]

Table 4-9:

MMC Debug Levels

Bit

Name

Description

0 (LSB)

Error Logging Enable

If set to 1, the MMC outputs error/diagnostic messages
onto the serial debug interface.

Low-level Error Logging Enable

If set to 1, the MMC outputs low-level error/diagnostic
messages onto the serial debug interface.

Alert Logging Enable

If set to 1, the MMC outputs important alert messages
onto the serial debug interface.

Payload Logging Enable

If set to 1, the MMC provides a trace of SIPL activity on
the payload interface onto the serial debug interface.

IPMB Dump Enable

If set to 1, the MMC provides a trace of IPMB messages
that are arriving to/going from the MMC via IPMB-L.

5-7

Reserved

Содержание AMC123









































































































Результаты поиска

Содержание AMC123

Отзывы:

Бренды по названию

Популярные бренды

PT AMC123, Руководство пользователя

Результаты поиска

Содержание AMC123

Отзывы:

Бренды по названию

Популярные бренды