Psion Teklogix OMNii HDK XT10 Скачать руководство пользователя | Manualshive

Страница: 30 / 192

background image

Chapter 3: Hardware

Identifying Hardware

20

Psion Teklogix Omnii HDK User Manual

3.4

Identifying Hardware

An overview of the operating system and the installed hardware on Omnii can be viewed by
opening the System applet in the Windows Control Panel.

3.5

The LEDs

Omnii has four LEDs in the top left corner of the display bezel. From left to right the colors of
the LEDs are green/red/yellow, yellow, blue, and green/red/yellow. The yellow LED (second
from the left) can be controlled by applications with the Windows API; the name of this LED for
programming purposes is “Application”.

3.6

Connectors

In addition to the external docking connector on the base of the Omnii hand-held computer, the
following connectors exist on the main logic board:
•

Audio Expansion Connector

•

End-cap Expansion Connector (Expansion Port 1)

•

Pod Expansion Connector (Expansion Port 2)

•

100-Pin Multi-Function Connector (includes Expansion Port 3)

These connectors are described in detail in Chapter 6: “Omnii Expansion Ports and Connectors”.

3.6.1

Connector Locations

The following illustration shows the positions of the electrical connectors on the Omnii XT10
main logic board. These locations are shown in more precise detail in the drawing and model files
included with the HDK. See Section 5.4.1: “Physical Space Considerations” for details.

«
...
28
29
30
31
32
...
»

Содержание OMNii HDK XT10

































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для OMNii HDK XT10

Бренд: Hand Held Products Страницы: 12

POCKET PREP TSA-2400

Бренд: Franklin Страницы: 74

Бренд: SmarTerminal Страницы: 64

3C80501U - Vllx - OS 3.5 20 MHz

Бренд: Palm Страницы: 310

Handheld Device

Бренд: Ogo Страницы: 100

ToughBook CF-P2 Series

Бренд: Panasonic Страницы: 72

Бренд: Panasonic Страницы: 40

Toughbook CF-P1 Series

Бренд: Panasonic Страницы: 52

Бренд: Panasonic Страницы: 36

Toughbook CF-U1AQC2ZAM

Бренд: Panasonic Страницы: 10

Бренд: Panasonic Страницы: 64

Бренд: Panasonic Страницы: 236

Бренд: WTC Страницы: 137

Бренд: PAX Страницы: 247

Бренд: MilDef Crete Страницы: 54

Бренд: MilDef Страницы: 51

Бренд: MilDef Crete Страницы: 55

Бренд: cascade corporation Страницы: 4

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды