Federal Communication Commission Interference Statement
This equipment has been tested and found to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference in a residential installation. This equipment generates uses and can
radiate radio frequency energy and, if not installed and used in accordance with the instructions,
may cause harmful interference to radio communications. However, there is no guarantee that
interference will not occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by turning the equipment
off and on, the user is encouraged to try to correct the interference by one of the following
measures:
-Reorient or relocate the receiving antenna.
-Increase the separation between the equipment and receiver.
-Connect the equipment into an outlet on a circuit different from that to which the receiver is
connected.
-Consult the dealer or an experienced radio/TV technician for help.
FCC Caution: Any changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate this equipment.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two
conditions: (1) This device may not cause harmful interference, and (2) this device must accept
any interference received, including interference that may cause undesired operation.
This equipment complies with FCC RF radiation exposure limits set forth for an uncontrolled
environment. To maintain compliance with FCC RF exposure compliance requirements, please
avoid direct contact to the transmitting antenna during transmitting.
RF Exposure Warning!
This device contains transmitters and receivers which emit Radio Frequency (RF) energy. The device
is designed to comply with the limits for exposure to RF energy set by the Federal Communications
Commission (FCC) of the United States, Industry Canada (IC), and the regulating entities of other
countries.
If you are still concerned about exposure to RF energy,
you can further limit your exposure by limiting the amount
of time you use the equipment or by placing more distance
between your body and the device, since exposure level
drops off dramatically with distance.
911 Mariner St., Brea, CA 92821
PH: 714.257.0300 FAX: 714.257.0600
TOLL FREE: 800.666.2654
WWW.PRYME.COM
Support and Warranty
PRYME Radio Products warrants this product against defects in materials or workman-
ship for a period of one year from the date of retail purchase. PRYME will repair or
replace a defective unit, at our option, without charge for parts or labor. The limited
warranty is extended only to the original purchaser and is valid only to consumers in the
United States and Canada. It does not cover damage or failure caused by or attributable
to Acts of God, abuse, misuse, improper or abnormal usage, faulty installation, improper
maintenance, lightning, or other incidences of excessive voltage, or any tampering or
repairs by other than a PRYME authorized repair facility. It does not cover replacement
of consumable parts, transportation costs, or damage in transit.
Repair or replacement under the terms of this warranty does not extend the terms of
this warranty. This warranty can only be modified by an officer of PRYME Radio Products,
and then only in writing. Should this product prove defective in workmanship or
material, the consumer’s sole remedies shall be such repair or replacement as provided
by the terms of this warranty. Under no circumstances shall PRYME Radio Products be
liable for any loss or damage, direct, consequential, or incidental, arising out of the use
of or inability to use this product. Some states do not allow limitations on how long an
implied warranty lasts or the exclusions or limitations of incidental or consequential
damages, so the above limitations or exclusions may not apply to you. This warranty
gives you specific legal rights. You may also have other rights, which may vary, from
state to state.
For support or warranty service on your PRYME product, contact us at 1-800-666-2654
or visit us on the web at www.PRYME.com.
Copyright and Trademark Info
© 2015 PRYME Radio Products, Brea CA. All rights reserved.
PRYME® and PRYMEBLU® are trademarks owned by PRYME Radio Products.
All other product or service names are the property of their respective owners.
DISCLAIMER: The Bluetooth wireless link used by PRYMEBLU products is an open
standard, unsecured technology. As such, it is not recommended for first-responder
or other mission critical users.
4
Version 1.0.DIR August 2015
Testing and Using the PRYMEBLU Adapter
STEP THREE: Transmit and Receive Operation
Once your PRYMEBLU Adapter and wireless Bluetooth headset have been paired together:
Received signals will be heard over your Bluetooth headset’s speaker
When transmitting, the operator’s voice is picked-up by the microphone in the
Bluetooth headset
Push-to-Talk can be activated one of three ways:
• By pressing and holding the Talk button on the PRYMEBLU Adapter
• Using an optional PRYMEBLU Wireless Bluetooth PTT (model BT-PTT2 (sold separately)
• By pressing and holding the PTT button on the side of the two-way radio.
If you are using a PRYMEBLU PTT2, you will first need to pair the adapter with the
PTT device, using the instructions located in the PRYMEBLU PTT2 User’s Guide.
Status LED Messages
Troubleshooting
My wireless audio accessory will not pair with the PRYMEBLU Adapter.
Follow the instructions to place the PRYMEBLU Adapter into the correct pairing mode and then activate the
pairing mode on the accessory. Make sure that the PRYMEBLU Adapter and accessory being paired are within
one meter of each other.
My wireless audio accessory or worked before, but is not working now.
Make sure that the PRYMEBLU adapter is properly connected to the 2-way radio and that the radio is turned on.
Ensure that your wireless audio accessory and the PRYMEBLU Adapter both have fully charged batteries and are
turned on. If the devices will still not work, re-pair the PRYMEBLU adapter to the wireless accessory.
The meanings of the various status LED messages shown
by the PRYMEBLU Adapters are shown on the following table:
LED MESSAGE
One single blue
fl
ash per second
Two blue
fl
ashes per second
Three blue
fl
ashes per second
One long blue
fl
ash for 3 seconds
No indica
ti
on
MEANING
Normal opera
ti
on
Headset pairing mode ac
ti
ve
PRYMEBLU PTT pairing mode ac
ti
ve
Successfully paired or re-paired
Adapter is powered
off
