Prozone CSS20, Руководство пользователя

Страница: 4 / 16

4
INITIAL SALT DOSAGE
Maintain a salinity level of 2,000 ppm to 2,500 ppm. Refer to chart below. Pool gallons can be determined from the following formulas:
a. Rectangular – Length x Width x Average Depth x 7.5 (for gallons) or 1000 for liters.
b. Round – Diameter x Average depth x 5.9 (for gallons) or 785 for liters.
c. Oval – Length x Width x Average Depth x 6.7 (for gallons) or 893 for liters.
Salt ppm 1,500 2,000 2,200 2,400 2,600 2,800 3,000
Pool Size in Gallons
8,000 Gallons 100 134 147 160 174 187 200
10,000 Gallons 125 167 184 200 217 234 250
12,000 Gallons 150 200 220 240 260 280 300
14,000 Gallons 175 234 257 280 304 327 350
16,000 Gallons 200 267 294 320 347 374 401
18,000 Gallons 225 300 330 361 391 421 451
20,000 Gallons 250 334 367 401 434 467 501
24,000 Gallons 300 401 441 481 521 561 601
26,000 Gallons 325 434 477 521 564 608 651
28,000 Gallons 350 467 514 561 608 654 701
30,000 Gallons 376 501 551 601 651 701 751
32,000 Gallons 401 534 587 641 694 748 801
34,000 Gallons 426 567 624 681 738 794 851
36,000 Gallons 451 601 661 721 781 841 901
38,000 Gallons 476 634 698 761 824 888 951
40,000 Gallons 501 668 734 801 868 935 1001
RECOMMENDED SALT TYPE AND HOW TO ADD
Type of Salt:
1. Use food grade type of salt (evaporated and granulated) or salt formulated for use with salt chlorine generators.
2. WARNING: Do not use salt that contains ‘Prussiate of Soda’ (Prussiate of Soda is an anti-caking agent which contains iron).
This type salt may cause yellow stains on your pool bottom if left there without being dissolved.
3. WARNING: Do not use ‘rock salt’ which has dirt mixed in with the salt.
4. NOTE: Calcium Chloride is not salt. Use Sodium Chloride only.
5. Water softener salt pellets (Sodium Chloride ) may be used but will take longer to dissolve.
Adding Salt:
1. Never add salt to the ‘skimmer’ box, however the coarse salt granules may cause the pump impeller to seize.
2. Always disconnect any automatic cleaners before adding salt, and leave them off until all the salt has fully dissolved.
3. When pouring bags of salt into pool, pour away from skimmer and suction points. Sweep and brush with a pool broom until the salt dissolves
4. Keep the pump operating during this process.
SETTING THE CHLORINE LEVEL
1. When System is turned on initially the three LED’s on the right will blink continuously as follows:
SET-UP FUNCTION
LOW SALT
HIGH SALT
2. Press the MODE button and the three LEDS will begin flashing on and off together.
3. Press the MODE button again and the unit will enter the % SET UP MODE.
4. Select the % VALUE desired (10% is recommended to start ) by pushing the UP or DOWN buttons which will illuminate the desired
PERCENTAGE LEDs.
5. When the desired % VALUE is selected, press the MODE button to leave the % SET UP MODE. The chlorination cycle will begin.
6. The 100% VALUE setting should only be used to shock the pool.