Protool DCC-AGP 125, Оригинальная инструкция

Страница: 14 / 92

14
and more accurate dry cutting, concrete
or stone grooving by diamond discs. The
maximum depth of the cut can be set with
a sliding stop for cut depth [1-5], whose
position is secured with a stop screw [1-6].
When the cut depth is achieved, automatic
arrest is applied.This position is unlocked
with an arresting button [1-1]. In order to
enable safely putting away the exhaust cov-
er with a mounted cutting disc, the cover
is equipped with the top-position arresting,
which is unlocked with the arresting but-
ton [1-1] as well. Reduction of friction of
the exhaust cover on the workpiece and/or
damage of the workpiece surface are pre-
vented by wheels of the cover. The cut axis
can be watched in cut indicators [1-14], or
at the disc contact point with the workpiece
if the aperture cover [1-3] is opened. A
PROTOOL guide bar can be used to make
the cut guiding more accurate.
4.2 Use
Exhaust cover DCC-AGP 125 combined with
angle grinder PROTOOL (AGP 125-14 D or
AGP 125-14 DE), diamond discs and
PROTOOL suction adapter can be used for
dry grooving and cutting of stone or con-
crete.
Do not use quick-change nuts for clamping
the disc.
The user is fully liable for no-compliant use.
5 Safety instructions
WARNING!
The working safety requires that you read
these instructions for use and maintenance
and exactly follow these instructions.
►
Keep all attached documents and pass
the machine to other people only with
these documents.
►
Adhere to all safety guidelines which
come with every product.
►
Handle, assemble and set the cover with
the due care to avoid injuries.
►
By interconnecting the cover, grinder and
suction you get an assembly to which all
safety regulations and instructions val-
id for the grinder, suction and diamond
discs are applicable as well.
►
Before every use of the tool inspect the
fl exible power cord and power plug. Any
defects found must be repaired by an
expert.
►
This equipment must not be used in damp
and wet environments, in rain, fog, snow
and environments with a risk of explo-
sion.
►
If you carry out work during which the
tool might cut hidden electric cables, take
care to only hold the tool’s insulated han-
dles.
Safety regulations for cutting discs
►
Warning: Incorrect use of diamond tools
may cause their bursting with consequent
serious injuries.
►
Before clamping, visually check all dia-
mond tools for cracks or other possible
damage.
►
Never use damaged diamond tools.
►
When clamping, be careful about the di-
rection of rotation marked on the label
and/or the diamond tool, which must be
the same as the direction of the actual
rotation of the machine used.
►
The fl ange and fastening nuts must be
properly tightened.
►
Use a tool with speci fi cations suitable for
the worked material – cf. the information
on the diamond tool and its packaging.
►
Put the diamond disc vertically to the
cut.
►
Always apply oscillating cuts to let the
disc cool down and prevent overload of
the diamond disc.
►
After several cuts or intensive cutting
make a cool-down break to prevent over-
heating of the diamond tool.
►
Avoid mechanical damage to the diamond
tool, whether by force, impact or heat.
►
Do not use a diamond cutting disc for
grinding. Do not apply a lateral pressure
on a diamond cutting disc.
►
Diamond tools are self-sharpening. A
blunt tool is recognised by reduced cut-
ting power and a circular “ fi re” edge.
Short cuts into abrasive materials (lime-
stone/sandstone bricks, asphalt or gas
concrete) may sharpen a blunt tool. Spo-
radic sparks while cutting stone are typi-
cal and do not mean a critical problem.