PROTEKT 93-403 £ÓDZ ul. Starorudzka 9 POLAND TEL/FAX: (0 42) 683 03 21; 683 03 22
According to European standard EN 365:2004 and EN 795:2012 + A1:2000Type A a requirement to check the legibility of the product markings
Bearing element
Anchor point
Fig.1. Dimensions of the device AT183
1
Anchor device AT183 is a component of personal protective equipment against falls from a height. It is used to connect fall arrest
devices to the structural anchor point. Anchor device AT183 conforms the standard EN 795 type A - protection against falls from a
height - Anchor devices.
Anchor device AT183 is appropriate for a single person use only.
EN 795:2012
Ref.: AT183
Instruction Manual
ANCHOR
P O I N T
A T 1 8 3
T y p e A
Notified body, which
supervises the production of the equipment:
APAVE SUDEUROPE SAS -
CS60193
- 13322 MARSEILLE CEDEX 16 - FRANCE
CONSTRUCTION
Static strength -min.12kN
Material: Stainless steel ANSI304
Number of person: 1
IDENTITY CARD
PERIODIC EXAMINATION AND REPAIR HISTORY
1
2
DATE
REASON FOR
ENTRY PERIODIC EXAMINATION
OR REPAIR
3
4
SERIAL NUMBER
USER NAME
DATE OF MANUF.
DATE OF PUTTING
INTO OPERATION
DATE OF PURCHASE
IT IS THE RESPONSIBILITY OF THE USER ORGANISATION TO PROVIDE THE IDENTITY CARD AND TO FILL IN THE DETAILS REQUIRED.
THE IDENTITY CARD SHOULD BE FILLED IN BEFORE THE FIRST USE BY A COMPETENT PERSON, RESPONSIBLE INTHE USER ORGANIZATION FOR PROTECTIVE EQUIPMENT.
ANY INFORMATION ABOUT THE EQUIPMENT LIKE PERIODIC INSPECTIONS, REPAIRS, REASONS OF EQUIPMENT'S WITHDRAWN FROM USE SHALL BE NOTED INTO THE IDENTITY CARD BY A COMPETENT PERSON.
THE IDENTITY CARD SHOULD BE STORAGED DURING A WHOLE PERIOD OF EQUIPMENT UTILIZATION.
DO NOT USE THE EQUIPMENT WITHOUT THE IDENTITY CARD.
ALL RECORDS IN THE IDENTITY CARD CAN BE FILLED IN ONLY BY A COMPETENT PERSON.
MODEL AND TYPE OF EQUIPMENT
REF. NUMBER
DEFECTS NOTED,
REPAIRS CARRIED OUT
AND OTHER REVELANT INFORMATIONS
NAME AND SIGNATURE
OF COMPETENT PERSON
PERIODIC
EXAMINATION
NEXT DUE DATE
PROTEKT, 93-403 LODZ,
ul. Starorudzka 9, POLAND,
TEL: (48 42) 680 20 83, FAX: (48 42) 680 20 93
www.protekt.com.pl
Notified body which
supervises
the production of the equipment:
APAVE SUDEUROPE SAS -
CS60193
- 13322 MARSEILLE CEDEX 16 - FRANCE
*
during equipment utilization, especially:
- trailing or looping of cable or lifelines over sharp edges,
- any defects like cutting, abrasion, corrosion,
- climatic exposure,
- pendulum falls,
- extremes of temperature,
- chemical reagents,
- electrical conductivity.
*
personal protective equipment must be transported in the package (e.g.: bag made of moisture-proof textile or foil bag or cases made of
steel or plastic) to protect it against damage or moisture.
*
the equipment can be cleaned without causing adverse effect on the materials in the manufacture of the equipment. For textile products use
mild detergents for delicate fabrics, wash by hand or in a machine and rinse in water. Plastic parts can be cleaned only with water. When the
equipment becomes wet, either from being in use or when due cleaning, it shall be allowed to dry naturally, and shall be kept away from direct
heat. In metallic products some mechanic parts (spring, pin, hinge, etc.) can be regularly slightly lubricated to ensure better operation.
Other maintenance and cleaning procedures should be adhered to detailed instructions stated in the manual of the equipment.
*
personal protective equipment should be stored loosely packed, in a well-ventilated place, protected from direct light, ultraviolet degradation,
damp environment, sharp edges, extreme temperatures and corrosive or aggressive substances.
there are many hazards that may affect the performance of the equipment and corresponding safety precautions that have to be observed
