Pro's Kit GE-897, Руководство по сборке и инструкция

Страница: 31 / 36

29
依循以下指引並確認機器人是否依序動作
操作方式
How to Program Your Robot
掃地機器人
Sweeper
創意小畫家
Doodler
前 進
Forward
後 退
Backward
原地左轉
Left spin
原地右轉
Right spin
Forward right turn
向 左 前 轉
Forward left turn
向 右 後 轉
Backward right turn
向 左 後 轉
Backeard left turn
步驟
STEP
1
切換至模式
1
Switch to Mode 1
步驟
STEP
2
利用按鍵編程以設定機器人動作
/
行走路線
Set a path you want the robot to follow by pressing the buttons below.
操作指引
Operation Guide
向前
Forward
模式切換
Mode Switch
向左
Left
中央鍵
Central Button
向右
Right
完成
Finish
出發
Go
重複執行
Replay
向後
Backward
射擊
Shoot
Press the two buttons
simultaneously.
Press the two buttons
simultaneously.
Press the two buttons
simultaneously.
Press the two buttons
simultaneously.
向 右 前 轉
同時按下”向左”、”向前”兩個按鈕 同時按下”向右”、”向前”兩個按鈕 同時按下”向左”、”向後”兩個按鈕 同時按下”向右”、”向後”兩個按鈕
按鍵介紹
Keypad Instructions
Follow the instructions below. Make sure they are followed in sequence.
編程創意小畫家和掃地機器人
To Code Doodler & Sweeper
每次最多可輸入
64
個指令，當輸入第
65
個指令時，機器人會發出
”嗶
--------
嗶嗶”
(
一長音兩短音
)
警示聲拒絕接收指令
當遊戲狀態下，機器人發出”嗶-嗶-嗶”(三短音)警示聲時代表電
量過低，請更換電池，避免造成機器人損害或自動重啟
當機器人閒置超過一分鐘時將會發出”嗶-嗶”(兩短音)聲提示。
只需按任意鍵即可喚醒機器人並繼續遊玩。請注意，每當完成編
程時，必須按"完成"鍵代表結束編程，以利再次喚醒機器人時可
繼續執行所下指令；如未按下”完成”鍵，機器人休眠後將自
動消除指令記憶
若玩家不小心鍵入無法辨識之指令，例如同時按下左
/
右鍵或上
/
下鍵
，機器人將發出警示音，玩家不須再重置指令，直接繼續編程即可
You can input up to 64 commands with the keypad buttons. This
is the maximim number of inputs. Tribo will make a “Beeeee-
bee- bee” sound and stop taking the following orders when the
65
th input is made.
If Tribo emits a sound “Bee-bee-bee” while playing, it is on “low-
battery” alert. Please replace batteries with new ones. If the
batteries are not replaced, it could results in a crash or an
automatic re-boot.
Tribo will make a sound “Bee-bee” as a reminder when he’s been
left alone for more than 1 minute. To continue playing and wake
him up, simply press any button on the keypad.Please note any
finished coding program, with a press of “Finish” button as the
end, can still be executed when Tribo is woken up. However,
without pressing the “Finish” button to end the coding, the
unfinished program will automatically be erased after waking him up.
If users accidentally input non-recognizable codes, such as right
and left/up and down buttons at the same time, there is no need
to reset for re-coding. The robot should emit an alarm sound
and users can then finish the coding straight away from there.