SET-UP
1. Installing the battery into the car when the battery fully charged.
Pull off the battery cover lock on the bottom of the car (see diagram B). Connect the battery power plug (the
3-wire plug) into the car socket. The battery plug and the car’s socket fit only one way. Dot not force them
(see illustration C). then lock the battery cover properly.
2. Installing the batteries into the remote controller.
Open the battery cover on the bottom of the remote control (see diagram D). Insert 4 “AA” battery (not included)
into the battery component, ensuring to match polarity and replace the battery cover.
CHARGING THE BATTERY
1. Insert the battery charging plug (the 3-wire plug) into the charger's socket. The charging plug and the charger's
socket fit only one way. Dot not force them (see illustration A).
3. Plug the charger into a wall outlet. The charger's red charging indicator flashing to show that charging is in
progress.
4. Average charging time is approximately 4 hours. The high speed car operates for approximately
10 minutes on full charge.
5. The red charging indicator turns off when the battery is fully charged.
Note: the adaptor should be periodically examined for conditions that may result in the risk of fire, electric shock,
or injury to persons and that, in an event such conditions, the adaptor should not be used until properly repaired.
REMOTE CONTROL SPECIFICATIONS AND FUNCTIONS
1. Remote control functions:
- forward straight
- forward left
- forward right
- backward straight
- backward left
- backward right
- stop
2. Maximum speed: 40 MPH
3. Wireless transmission range: Up to 100 meter.
OPERATION
THIS IS A HIGH-SPEED OUTDOOR RC CAR. DO NOT PLAY INSIDE YOUR HOME OR OTHER SMALL ENCLOSED AREAS.
1. Turning your car on:
• Pick-up your car and turn over the car, so the under carriage is facing you. Make sure the battery
are properly installed and the battery compartment door is properly closed and locked.
• Sync your car and remote properly and set the car on the ground.
2. Driving your car:
• If you are right handed, use your left hand to hold the remote control. with one finger on the trigger, and
use your right hand to operate the control knob, If you are left handed, hold the remote in your right hand
and operate the knob with your left hand.
• Pull the remote’s trigger back halfway to drive forward at low speed. Pull the trigger completely back to
drive at high speed.
• Push the remote’s trigger forward to make car move in reverse.
• Turn the remote’s control knob to the left (i.e., counterclockwise) to turn the car left. Turn the knob to the
right (i.e., clockwise) to turn the car right.
• To break or quickly stop simply pull or push the remote’s trigger in the opposite direction.
BATTERY NOT INCLUDED (4XAA)
FEATURES
• R-2-R, COMPLETELY ASSEMBLED AND READY TO RUN
• 2.4 GHZ HOBBY GRADE RC TRUCK
• SPEEDS UP TO 40 MILES PER HOUR
• DIGITAL PROPORTIONAL STEERING
• 100 METER DRIVING RANGE
• GREAT BEGINNER HOBBY RC TRUCK
Thank you for purchasing the URBAN RENEGADE
™
High Speed Racer from Propel RC. Please read this
user manual carefully as it contains valuable information on how to properly fly and care for your
helicopter.
BATTERY
POWER
CHARG
E
A
B
C
D
AA
AA
AA
AA
OPEN
CAR DIAGRAM
REMOTE DIAGRAM
Shell Clip
Shell
Antenna
ON/OFF
Battery Compartment
Your URBAN RENEGADE
™
High Speed Racer
utilizes an automatic 2.4G channel selection system that
allows up to 8 people to fly side by side in the same wireless range.
For One Person Play:
1. Before starting, make sure that the power on both your controller and car are in the OFF
position. Make sure that there are no other 2.4G devices in the area as well.
2. Turn ON the car and set it down on a flat surface. The red LED indicators inside the car
body should flash.
3. Turn ON your remote. The remote power indicator light will flashing, then pull the trigger all the
way down and the remote will beep one time. the power indicator light should turn on. This
indicates that your car and remote have successfully synced. Should this not happen, repeat
all steps again.
For Multi Person Play:
4. Before starting, make sure that the power on all Cars and Controllers are in the OFF position.
Make sure that there are no other 2.4G devices in the area as well.
5. Each person will have to sync their car individually at a different time to avoid interference.
Follow steps 1 to 3 above making sure to keep away from other people while also making sure that
no one else is syncing at the same time.
6. After syncing a players car, it should be left ON until all players have synced their cars.
7. Should there be a mistake/interference, all players must turn off their controllers and cars
and start the process all over again.
SYNCING YOUR HIGH SPEED RACER
Antenna
Left & Right Trim
Forward & Backward Trim
Control Knob
Trigger
ON/OFF
Power Indicator
