background image

CREATE YOUR

 SMART HOME 

A SMARTER CHOICE

Size (WxH): 190x280 mm. Fold according to items BOP.

Manual v

ersion 1.3

Features 

•  Easy installation – no cables or connections are required
•  Self-programming with 67 million codes 
•  3 channels; 1 group function 
•  Each outlet has 5 memory settings 
•  The remote control operates at a distance up to 30 

metres (free line of sight)

•  Green LED indicates ON/OFF and programming status
•  The outlets are TellStick compatible.

WARNING! 

•  Do not place two outlets too close to each other. The 

distance between two outlets must be at least 1 m. 

•  DO NOT OVERLOAD THE SYSTEM! 

Do not use the system in humid places, e.g. in farms or basements 

and not in the vicinity of inflammable liquids, solvents, colours or 

similar products.

Installation 

1.  Remove the small plastic tab from the battery in the 

remote control.

2. Connect the outlet to the mains. 

3. Connect a lamp to the outlet. If there is a power switch on 

the connecting cable, make sure it is switched on.

Programming an outlet

1.  Install the outlet as explained under “Installation” above.

2. Keep the outlet programming button pressed for 3 

seconds. The LED blinks slowly.

3. Press one of the ON buttons on the remote control 

within 10 seconds to link the outlet to the button. (The 

programming mode is automatically disabled if no button 

is pressed.)

4. The connected lamp blinks twice as confirmation. 

Deprogramming a single code: 

1.  Keep the outlet programming button pressed for 3 

seconds. The LED blinks slowly.

2. Press the corresponding OFF button on the remote 

control to remove the programmed code. (The 

programming mode is automatically disabled after 10 

seconds if no button is pressed.)

3. The connected lamp blinks twice as confirmation. 

4. To add a new code, repeat the programming procedure.

Deprogramming all codes:

1.  Keep the outlet programming button pressed for 5 

seconds. The LED blinks rapidly.

2. Press the outlet programming button once more 

to remove all codes. (The programming mode is 

automatically disabled after 10 seconds if the button is 

not pressed.)

3. The connected lamp blinks twice as confirmation. 

4. To add a new code, repeat the programming procedure. 

ON/OFF operation of a remote controlled outlet 

1.  Press the ON button on the remote control to switch on 

the power. 

2. Press the OFF button to switch off the power.

3. Press the GROUP button to simultaneously switch all 

outlets ON or OFF.

4. ON/OFF switching is also possible by briefly pressing the 

outlet programming button.

The outlets have 5 memory settings 

It is possible to programme the outlet  to switch on 

separately or switch them on and off in different 

combinations.
Example: Suppose that three outlets were programmed, 

where outlet 1 controls a table lamp, outlet 2 controls a 

window lamp and outlet 3 controls a ceiling lamp. 
•  Outlets 1, 2 and 3 can be controlled separately using the 

ON and OFF buttons for each channel on the remote 
control. 

•  Also two of the outlets (e.g. 1 and 3) can be programmed 

to a single button. It is then possible to simultaneously 
control the table lamp and ceiling lamp. 

Note: Do not program an ON/OFF outlet and a dimmer outlet to the 

same remote control button. It is recommended to only program 

one dimmer outlet to each remote control button.

TellStick compatible

The outlets are compatible with TellStick products. Select 

“Proove” as the outlet type when programming the outlets 

for use in this manner.  Please visit www.telldus.com for 

more information on how to use the outlets with TellStick 

products.

Troubleshooting

Connected lamp does not light:

1.  If the outlet LED lights green:

•  Check the light source.
•  If there is a power switch on the connecting cable, 

make sure it is switched on.

2. If the outlet LED does not light green:

•  Check the power supply to the outlet.
•  Try pressing the ON button on the remote control 

once again.

3. If the problem persists:

•  Check the battery in the remote control 

(transmitter). 

•  Check the programmed codes. It may be necessary to 

erase old codes and reprogram the outlet.

Specifications 

Remote control (transmitter):  

Power supply:.   .   .   .   .   .   .   .   .   .   .   3V CR2032 battery (included)

Outlets (receiver): 

Load on/off function (max.): . . . . . . . . . . . . . . . . 1000W

Load on/off/dimmer function (min. - max.):.   .   .   .   .   .   40-300W

Operating range: . . . . . . . . . . Up to 30m (free line of sight)

Protection class: . . . . . . . . . . . . . . . . . . . . . . . . IP20

Class:.   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   .   . I

Operating temperature (max.): .  .  .  .  .  .  .  .  .  .  .  .  .  .  .  . 40°C

Frequency: . . . . . . . . . . . . . . . . . . . . . . .  433.92MHz

Power supply:  . . . . . . . . . . . . . . . . . 230V ~ ±10%, 50Hz

USERS MANUAL • TSP200

Отзывы: