Promotech BM-16 Скачать руководство пользователя страница 6

Страница: 6 / 28

BM-16

This document is protected by copyrights.

Copying, using, or distributing without permission of PROMOTECH is prohibited.

2. SAFETY PRECAUTIONS

1. Before beginning, read this

Operator’s Manual and complete proper occupational

safety and health training.

2. Use the machine only in applications specified in this Operat

or’s Manual.

3. The

machine

must

complete

and

all parts must be genuine and fully operational.

4. The specifications of the power source must conform to those specified on the

rating plate.

5. Never carry the machine by the cord and never pull the cord because this may

damage it and result in electric shock.

6. Untrained bystanders must not be present near the machine.

7. Before beginning, make sure that the correct is the condition of the machine,

power source, power cord, plug, control components, and milling tools.

8. Keep the machine dry. Exposure to rain, snow, or frost is prohibited.

9. Keep the work area well lit, clean, and free of obstacles.

10. Never use near flammable liquids or gases, or in explosive environments.

11. Use only tools specified in this

Operator’s Manual.

12. Never use tools that are dull or damaged.

13. Install the cutting inserts and milling head securely. Remove adjusting keys and

wrenches

from

the

work

area

before

connecting

the

machine

the power source.

14. Never use the machine in upside down position with the milling head facing up.

15. If the

cutting edge of the insert is worn, rotate the insert in the socket by 90° or

180° or, if all possible to use edges are worn, replace with a new insert specified in

this Operator’s Manual.

16. Before every use, inspect the machine to ensure it is not damaged. Check whether

any part is cracked or improperly fitted. Make sure to maintain proper conditions

that may affect the operation of the machine.

17. Always use eye and hearing protection, non-skid footwear, and protective clothing

during operation. Do not wear loose clothing.

18. Using the spindle lock button while either operating the machine or removing the

milling head is prohibited because this may damage the machine.

19. Do not touch moving parts or metal chips formed during milling. Prevent objects

from being caught in moving parts.

Содержание BM-16





























Результаты поиска

Содержание BM-16

Отзывы:

Бренды по названию

Популярные бренды

Promotech BM-16, Руководство оператора

Результаты поиска

Содержание BM-16

Отзывы:

Бренды по названию

Популярные бренды