Prominence Home 51676 Скачать руководство пользователя страница 5

Страница: 5 / 14

WARNING:

To avoid risk of electric shock, be sure to shut off power at the main fuse or circuit breaker box before

installing or servicing this fixture. Turning off the electrical power by using the light switch is not

sufficient to prevent electrical shock.

To reduce the risk of injury, install the fan so that the blades are at least 7 feet (2.1 Meters) above the

floor and at least 18 inches (0.5 Meters) from the tip of the blades to the wall.

To reduce the risk of fire, electric shock, or personal injury, mount to outlet box marked “acceptable for

fan support” and use mounting screws provided with the outlet box.

The installation has to be in accordance with the National Electrical Code, ANSI/NFPA 70-1999 and

local codes. If you are unfamiliar with the methods of installing electrical wiring, seek the services of a

qualified licensed electrician.

Using a full-range dimmer switch to control fan speed will cause a loud humming noise from the fan. To

reduce the risk of fire or electric shock, do NOT use a full-range dimmer switch to control the fan speed.

SAFETY INSTRUCTIONS

Содержание 51676














