Prolitec AirQ 1280 Скачать руководство пользователя страница 56

AirQ 1280

56

Applications

The Prolitec approach to odor remediation uses a proprietary and patented neutralizer that inhibits 
the human olfactory system from detecting the odor and then injecting a small amount of scent to 
create an ultra-low concentration in the air of less than 1 ppm. This approach is unique and much 
more effective than traditional approaches that simply douse the odor with a high concentration of 
scent. 

Aromatherapy and Performance Scenting

It is well known that scent has a powerful impact on human emotion and behavior. The use of 
scent to influence human emotion is just like Ambient Scenting but with a specific objective for the 
occupants of the treated space. The use of scent and the essential oils of flowers, herbs and trees 
to promote health and well being is the well-established branch of alternative medicine known as 
aromatherapy. It is also recognized that scent can be used to optimize performance in the workplace. 
The benefits include reduced errors in routine functions, increased employee sense of well being, 
higher morale, improved customer service and overall improved productivity.

AirQ 1280 and Prolitec aromatherapy chemistry can help make a workspace a more comfortable and 
appealing place to be. As examples of the positive effect of aromatherapy on the workplace, below 
are results of several relevant studies:

•  A 1991 study demonstrated that “sustained attention tasks” were performed with greater 

accuracy by the participants in scented rooms compared to those in the non-scented control 
rooms.

1

•  Another study found that fragrance had a dramatic and positive effect on a proofreader’s 

efficiency.

2

•  It is commonly known that the Tokyo Stock Exchange diffuses peppermint into the air in the 

afternoons to make the brokers feel invigorated.

_______________

1

 Dr. Joel Warm and Dr. William Dembar. “Olfactory Stimulation and Sustained Attention.” 

Compendium 

of Olfactory Research

, (Dubuque, Iowa: Kendall/Hunt Publishing Co., 1995) p. 47.

2

 Mark Kilauga et al. “Consumer Panel Study on the Effect of Peppermint and Lavender Fragrances on 

Proofreading.” 

Compendium of Olfactory Research

, (Dubuque, Iowa: Kendall/Hunt Publishing Co., 1995) 

p. 131

14

Содержание AirQ 1280




























































Отзывы: