background image

Page 4 of 5

STep 1

Lay out all the included components and hardware 
to ensure you have everything listed on the parts page. 
Take four of the self-adhesive Noise Attenuation Pads (P5) 
and place them on the VT Brackets (P4) as shown. 

STep 2 

Place the VT Brackets (P4) on the underside of the 
surface you will be lifting. Use the included 24 Wood Screws (P13) 
to attach the Brackets in place, using six screws per bracket. 

STep 3

Place the 4 Legs (P1) into the 4 VT Brackets (P4) as shown. 
Using the supplied Allen Wrench, loosely thread the M6X14 
Machine Screws (P12) into the remaining holes on each of the 
VT Brackets (P4) to secure the 4 legs (P1). Once all screws are 
in place, fully tighten all four screws.  

STep 4

Now that the Legs (P1) are secure you can attach the 4 
Stand-Offs (P2) and 4 Glides (P3) to the bottom of each leg 
as shown. Secure the Stand-Offs (P2) and Glides (P3) with the 
remaining M6X14 Machine Screws (P12), 4 per leg. 

STep 5

Attach 

the

 

Control Box (P6) to the underside of your surface 

using two of the M5X16 Screws (P14) per box. Make sure you 
leave enough room for cable connections into the wire ports 
on each box. Next 

f

ind a suitable area to place your Remote 

(P8), we recommend somewhere on the end of your surface 
along the front edge. Once you’re happy with its position 
you can attach it using 2 x M5X16 Screws. 

STep 6

Now that everything’s in place we can start connecting it all 
together. Take the CB Cable (P10) and connect the control 
boxes together via the small ports located on the side of the 
boxes. Connect the remote (P8) to 

the 

Control Box 

(

P6). 

Use the 4 LC Cables (P9) to connect each Leg (P1) to the 
Control Box (P6). Finally take the 2 Power Cables (P11) and 
connect each one to 

the 

control box. Use the included 

adhesive-backed Cable Clips (P15) to secure all the wires so 
they don’t get tangled. 

STep 7

Once you have everything connected and secure, carefully turn 
your surface right-side-up. We recommend using at least 2 
people to do this. Adjust the pre-installed Glides (P3) as needed. 

STep 8

Plug the Power Cables (P11) from 

the

 

Control Box (P6, P7) into an outlet. 

imporTanT

You MUST reset the table lift prior to use. 

reSeT proCedure

If you’ve raised the table lift at all then press and hold the 
down button on the Remote (P8) until the lift is at its lowest, 
then release the button. Then press and hold the down 
button for 10 seconds until the LED display reads “ASr”. If 
you are using a spare remote without LED then hold onto the 
down button for about 10 seconds then release. 

Press and hold the down button one more time until the desk 
lowers a bit more, slightly rises and then stops. Release the 
button and your table lift is now ready for action.

You can preset up to 4 positions by following this simple 
procedure. Use the up/down buttons on the remote to find 
your desired height(s), then press “M” followed by a number 
1-4., then wait a few seconds until the height is displayed

 

again. To move to the set position, hold the number button.

Caution: Double-check that the wood screws 

(P13) are short enough that they won’t puncture a 

hole in your surface when screwed in completely

Ensure the boxes and remote are placed so the 

wires can reach between everything

If your surface is not pre-drilled we recommend 

you pre-drill any holes needed for the VT Brackets 

(P4). Never use countersunk screws

As stated earlier make sure the screws are short 

enough that they don’t puncture a hole in your 

surface when screwed in completely. Do not 

overtighten the screws here, overtightening may 

cause damage to the components.

aSSembLy inSTruCTionS

how To order

1.800.676.6123     |     

sales@progressiveautomations.com

     |     

www.progressiveautomations.com

Отзывы: