Progress Lighting AirPro P2560 Скачать руководство пользователя страница 11

Attaching the Fan 

Blades

1.  Align the holes in the strength plate and 

holes in the blade with holes in the blade 

arm and secure with the screws provided 

(Figure 12).

2.  Repeat for the remaining blades. 

Figure 12

Figure 13

Blade Balancing

All blades are grouped by weight. Because 

natural woods vary in density, the fan may 

wobble even though the blades are weight 

matched.
The following procedure should correct most 

fan wobble. Check after each step.
1.  Check that all blade screws are secure.
2.  Most fan wobble problems are caused 

when blade levels are unequal. Check this 

level by selecting a point on the ceiling 

above the tip of one of the blades. Measure 

from a point on the center of each blade 

to the point on the ceiling. Measure this 

distance as shown in Figure 13. Rotate 

the fan until the next blade is positioned 

for measurement. Repeat for each blade. 

Measurements deviation should be within 

1/8”. Run the fan for 10 minutes.

Touching

Ceiling

STANDARD CEILING MOUNTING

1.  Align the locking slots of the ceiling 

canopy with the two screws in the 

mounting plate. Push up to engage the 

slots and turn clockwise to lock in place. 

Immediately tighten the two mounting 

screws firmly.

2.  Install the remaining two mounting screws 

into the holes in the canopy and 

tighten firmly.

3.  Install the decorative canopy ring by 

aligning the ring’s slots with the screws in 

the canopy. Rotate the ring clockwise to 

lock in place.

4.  You may now proceed to attaching the 

fan blades.

3.  Make sure that canopy is tightened securely 

to ceiling mounting bracket and that the 

ceiling mounting bracket is tightened 

securely to the electrical box.

4.  Interchanging two adjacent blades can 

redistribute the weight and possibly result 

in the smoother operation.

5.  Use the enclosed Blade Balancing Kit if the 

blade wobble is still noticeable.

8. Finishing the Fan Installation

Strength plate

Blade

Blade arm

Screws

Connecting the Safety 

Cable

Turn the wood screw (not provided) into the

1.

ceiling.

Place the looped end of the safety cable onto 

2.

the wood screw and then tighten the screw firmly,

or connect the safety cable directly to the outer joist.

Содержание AirPro P2560
















Отзывы: