Progress Lighting AirPro P250071 Скачать руководство пользователя страница 11

1.  Check that all blade screws are secure.
2.  Most fan wobble problems are caused 

when blade levels are unequal. Check this 

level by selecting a point on the ceiling 

above the tip of one of the blades. Measure 

from a point on the center of each blade 

to the point on the ceiling. Measure this 

distance as shown in Figure 16. Rotate 

the fan until the next blade is positioned 

for measurement. Repeat for each blade. 

Measurements deviation should be within 

1/8”. Run the fan for 10 minutes.

3.  Make sure that canopy is tightened securely 

to ceiling mounting bracket and that the 

ceiling mounting bracket is tightened 

securely to the electrical box.

4.  Interchanging two adjacent blades can 

redistribute the weight and possibly result 

in the smoother operation.

5.  Use the enclosed Blade Balancing Kit if the 

blade wobble is still noticeable.

Figure 16

Blade Balancing

All blades are grouped by weight. Because 

materials vary in density, the fan may wobble 

even though the blades are weight matched.
The following procedure should correct most 

fan wobble. Check after each step.

Touching

Ceiling

8.

Finishing the Fan

Installation

STANDARD CEILING MOUNTING

1.  Align the locking slots of the ceiling 

canopy with the two screws in the 

mounting plate. Push up to engage the 

slots and turn clockwise to lock in place. 

Immediately tighten the two mounting 

screws firmly.

2.  Install the remaining two mounting screws 

into the holes in the canopy and tighten 

firmly.

3.  Install the decorative canopy ring by 

aligning the ring’s slots with the screws in 

the canopy. Rotate the ring clockwise to 

lock in place. (Figure 15)

WHEN USING THE STANDARD BALL/DOWNROD 

MOUNTING, THE TAB IN THE RING AT THE 

BOTTOM OF THE MOUNTING PLATE MUST 

REST IN THE GROOVE OF THE HANGER BALL. 

FAILURE TO PROPERLY SEAT THE TAB IN THE 

GROOVE COULD CAUSE DAMAGE TO WIRING.

Figure 15

Содержание AirPro P250071
















Отзывы: