Int phn.+46 371-52 32 90
www.profsafe.se
Sida/Page 3 av/of 4
User manual code lock
(for more information see full user manual for the electronic code lock).
NOTE! At frequent daily openings the code should be replaced at least once per year to reduce wear on the keypad.
When the batteries are low the lock indicates with numbers of short beeps after opening of the safe. You find the batterybox
on the inside of the door. (If you need to connect the battery from outside you can find additional battery pools under
the plastic to the right of the keypad).
Introduktion
Som standard er boksen udstyret med en elektronisk kodelås med mulighed for tidsforsinkelse.
Efter modtagelsen af boksen, skal du omhyggeligt kontrollere for transportskader (eventuelle transportskader skal altid meddeles skriftligt til transportfirmaet ved
modtagelsen). Anbring boksen på sin plads. I bunden findes 2 forankringshuller. Boksen er forsynet med dobbeltklæbende tape på bunden for montering på en
hylde.
Garanti
Boksen har 12 måneders garanti mod fabrikationsfejl forudsat at denne manual følges i sin helhed. Garanti på låsen er 12 måneder, men dækker kun udskiftning af
dele med fejl. Eventuelle arbejdsomkostninger for adgang til låsen omfattes ikke af garantien.
To open (without time delay):
2.
Enter the valid code (the delivery code is always 123456), the
lock confirmed with double beep.
3.
The safe is now ready to open.
To open (with time delay):
1.
Enter the valid code (the delivery code is always 123456).
2.
If you have dialled the correct code the lock confirms with a
double beep after the last digit. Now the time delay starts.
3.
When the time delay has passed the open period starts (the lock
indicated every two seconds).
4.
Enter your valid 6 digits code again (if correct code is entered
the lock confirms with double signal after the last digit).
5.
The safe is now ready to open.
To set the time delay (max. 99 min) and open period
(max. 19 min):
Press and hold digit (9) until the lock confirms with a double beep. The
diode remains lit during the following action:
1.
Enter the valid “Manager code” (double beep if correct valid
code).
2.
Enter the value for the desired time delay and open period
(double beep ) For example of you want to program 26 minutes
time delay and 12 minutes open period, dial “2612”.
3.
Enter the value for the desired time delay and open period again
to confirm (the lock confirms with double beep).
NOTE! To be able to set a longer time delay than already set on the lock,
the lock must be in “opening period”. Dial the valid manager code, wait
until the time delay has passed and the lock is in open period (beep/blink
every two seconds). Follow the instructions above.
To change code: (door open)
Press and hold digit (O) until the lock confirms with a double beep.
The diode remains lit during the following action:
1.
Enter the old code (the lock confirms with double beep).
2.
Enter a new code (double beep) and repeat the code once more
(double signal).
If something goes wrong you hear a long signal, the old code remains
valid.
To add the second user code:
Press and hold digit (1) until the lock confirms with a double beep.
The diode remains lit during the following action:
1.
Enter the manager code.
2.
Enter the second user code twice (after every time the lock
confirms with double beep).
The second user code and be changed the same way as the manager code.
With the manager code you can block the second user code but the
manager code can never be blocked.
To erase the second code: (only in manager mode)
Press and hold digit (3) until the lock confirms with a double beep.
The diode remains lit during the following action:
1.
Enter the manager code
The second code is now blocked.
