background image

9

8. Insert the indicated connectors into the Right

Upright (78). 

Next, insert the fronts of the brackets on the
Bridge (95) into the Uprights (74, 78), and then
fully insert the brackets. Make sure that the plas-
tic edges of the Bridge are inside the Uprights.

Attach the Bridge (95) with six 1/4" x 1/2" Bolts
(7) and six 1/4" Star Washers (10); 

start all six

Bolts and then tighten them.

See steps 4 and 6.

Tighten the four 3/8" x 4 1/2"

Bolts (6). 

10

7

95

Connectors

Front

Edge

74

78

10

7

7

7

8

9. With the help of a second person, hold the con-

sole assembly near the Bridge (95). Connect the
Bridge Wire (52) to the console wire. 

See the

inset drawing in step 7. The connectors
should slide together easily and snap into
place.

If they do not, turn one connector and try

again. 

IF THE CONNECTORS ARE NOT CON-

NECTED PROPERLY, THE CONSOLE MAY
BE DAMAGED WHEN THE POWER IS
TURNED ON. 

Connect the Console Ground Wire (101) to the
console assembly ground wire. Insert the wires
into the console assembly.

Attach the console assembly with three 3/8" x
1 1/4" Bolts (5) and three 3/8" Star Washers (9).

Be careful not to pinch the wires.

10. Identify the Storage Latch (53). Remove the tie

from the end of the tube. Make sure that the
sleeve has been slid over the indicated hole and
that the Latch Knob (54) is locked into the indi-
cated hole. 

Pull on the sleeve to make sure

that it is locked into place.

10

54

Sleeve

Hole

Tube

53

Console

Assembly

101

95

5

9

9

Console

Wires

52

Содержание 9.0 Competitor Treadmill

































Отзывы: