13
ZVC762-004PR_v01
While pulling out the cord pay attention to the
yellow stripe which signals the end of the cord.
Further attempts (pulling on cord) may result in
damaging the cord.
●
Plug in the appliance.
Before switching on the vacuum cleaner
with the on/off button, make sure that the
appropriate module is installed in the container
(see section C, E, or F).
12
Switch on the vacuum cleaner by pressing the “on/off”
button.
In order to prepare the vacuum cleaner for wet operation
additionally:
13
Assemble the spray unit – the suction hose handle
attachment.
●
Attach the hose fastenings to the suction hose and the
telescopic suction tube.
14
Attach the end of the hose (sleeve) to the telescopic
suction tube and insert the other end of the hose in the small
atomizing nozzle or the large atomizing nozzle until you hear
a characteristic click.
15
Use the following nozzles for the wet vacuuming and wet
cleaning function or to pick up water: large atomizing nozzle,
small atomizing nozzle or the water pick up nozzle.
16
Slide the stub pipe valve plug downwards.
●
Insert the stub pipe of the hose to the valve in the
vacuum cleaner housing.
●
Make sure the stub pipe fastenings snap shut.
In case of difficulties in connecting the above
mentioned elements moisten the gaskets e.g.
with technical vaseline, water, etc.
Vacuum cleaner functions
TRADITIONAL CLEANING WITH SAFBAG DUST BAG
1
Press and hold the container lid opening button and lift
the container lid.
2
Put the SAFBAG holder into the container. Make sure the
holder is inserted correctly in the container guide slots and
the safety lock is engaged. Unfold the bag in the container.
Do not put SAFBAG holder into a wet container.
Thoroughly dry a wet container. SAFBAG dust
bag must not get wet.
3
Cover the container with the filtration unit.
If the SAFBAG holder is not attached properly,
the safety lock will prevent covering the
container with the filtration unit.
●
Prepare the vacuum cleaner for operation according
to section B.
C
4
The vacuum cleaner starts at the same power level it
had been working before it was turned off. Set the desired
power value by pressing the power adjustment b/-.
The vacuum cleaner is equipped with a power
level memory function. When you turn off the
vacuum cleaner using the ON/OFF button, the
power level is going to be stored in memory.
After the vacuum cleaner is turned on next
time, it is going to start working at the same
power level it had been working before it was
turned off.
The vacuum cleaner is equipped with the
adjustment function for LED brightness of
the power level indicator and the clogged
air inlet indicator situated on the control
panel. To set demanded brightness of LEDs
you should simultaneously press the power
adjustment b and –, and then holding
them down you should turn on the vacuum
cleaner by pressing the “ON/OFF” button.
The LED for power levels MIN, 2, and MAX
turn on, and the motor stays turned off. Next
by pressing the power adjustment b/–
you can respectively increase or decrease the
brightness of power level indicator, and the
clogged air inlet indicator. It is not possible
to change LED brightness for the pump
operation indicator. After setting a desired
LED brightness, it is necessary to turn off the
vacuum cleaner using the ON/OFF button.
In this way you leave the LED brightness
adjustment function mode, and the set LED
brightness level is stored.
The vacuum cleaner is equipped with a power
limiting function should the inlet opening be
clogged or the SAFBAG dust bag full. It is
manifested by a pulsing limitation of the motor
power and the lighting up of the clogged air
inlet indicator while the vacuum cleaner is
operating at full power. In such a case switch
off the vacuum cleaner by pressing the on/
off button, unplug the appliance and clear the
tubes or replace the SAFBAG dust bag.
SAFBAG dust bag disassembly/assembly
1
Remove the filtration unit from the container and pull out
the SAFBAG holder.
2
Lift the SAFBAG tab and slide the dust bag from the
holder guide.
3
Slide the new SAFBAG tab all the way into the holder
guide as directed by the arrow printed on the bag until tab
locks in the guide.
4
Put the SAFBAG holder in the container and cover with
the filtration unit in accordance with paragraphs
C2
and
C3
.
D
