Panel PC
Quick start guide
2
It is preferred not to use
power tools to attach the
device to a mount or
stand.
How to start:
Step 1: Take contents out of the box, make sure all components are present.
Step 2: Install wall/glass mount or desk stand using manual screw driver, check designated mount/
stand manual for instructions.
Step 3: Connect to power via power adapter or PoE+.
Step 4: Connect to Internet through Wi-Fi or PoE+.
Step 5: If applicable, install and configure preferred application.
Quick connection settings
Step 1: Plug in PoE+ cable or
optional
power adapter to turn on display. If using PoE+ for both power and data,
this was the final step. If connection to Wi-Fi is preferred, swipe up in the home menu to arrive in the app drawer.
Once there, select Settings.
Step 2: In the settings menu, go to Network & internet, located at the top of the menu.
Step 3: In the Network & internet menu, select Wi-Fi.
Step 4: Turn on Wi-Fi and select desired Wi-Fi network, fill in credentials to connect to internet.
Optional accessories
Landscape
Barcode scanner
NFC module
3
Camera
4
Portrait
Tools necessary
but not included
Caution:
Please note this product contains a small clock battery. Please return the product to a
certified repair centre for proper replacement of the battery; battery disposal can be
dangerous.
WARNING:
Changes or modifications to this unit not expressly approved by the party responsible
for compliance could void the userʼs authority to operate the equipment.
NOTE:
This equipment has been tested and found to comply with the limits for a Class A
digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interference when the equipment is
operated in a commercial environment. This equipment generates, uses, and can
radiate radio frequency energy and, if not installed and used in accordance with the
instruction manual, may cause harmful interference to radio communications.
Operation of this equipment in a residential area can cause harmful interference, in
which case the user will be required to correct the interference at their own expense.
This device complies with Part 15 of the FCC Rules. Operation is subject to the
following two conditions: (1) This device may not cause harmful interference, and (2)
this device must accept any interference received, including interference that may
cause undesired operation.
Europe/UK – EU/UK Declaration of Conformity
This device complies with the essential requirements of the Radio Equipment Directive
(2014/53/EU). The following test methods have been applied in order to prove
presumption of conformity with the essential requirements of the Radio Equipment
Directive. This equipment is compliant with Class A of EN 55032. In a residential
environment, this equipment may cause radio interference.
Correct Disposal of this product
This marking indicates that this product should not be disposed of with other
(household) waste. To prevent possible harm to the environment or human health
from uncontrolled waste disposal, recycle it responsibly to promote the sustainable
reuse of material resources. To return your used device, please use the return and
collection systems or contact the reseller where the product was purchased. They can
take this product for environmentally safe recycling.
“FCC & CE RF Radiation Exposure Statement Caution: To maintain compliance with the
FCC & CEʼs RF exposure guidelines, the product must be placed at least 20 cm from
nearby persons.”
The recommended temperature for the ProDVX Display and accessories is 0°C-45°C.
APPC-10SLB / APPC-10X Quick start guide
This package contains:
Backside
Pogo
p
in connector
Strain relief
Speaker
Speaker
Wall / glass mount
VESA 75 mount
Screw spec: M4*4 mm
Bottom view
LAN port
Type A USB port
Micro-USB / OTG
GPIO
Mounting screw hole
HDMI out
Audio port 3.5 mm
12 V DC-in
Top view
On / off button
SD-Card slot
(with cover)
Back / home button
Scroll up / down button
Volume + and -
DC power adapter 12 V
1
Power plugs for Europe, UK & US
1
1
DC power adapter 12 V and power
plugs are only included with the
APPC-10X.
3
Does not work if your product has an internal NFC module.
4
Does not work with the APPC-10XP (Camera)
.
Phillips
screwd
ri
ver
2
