For any communication with the distributor,
please indicate the identification sticker data of
the product. The sticker is applied on the side
of the compressor.
2
3 - FOR YOUR SECURITY
6 - COMMUNICATION- TRACKING PRODUCT
The air delivered by your compressor allows you
to use many tools, ensure conditions: advice, in
certain cases USE RESTRICTIONS of air tools
using air pressure.
Avoid any degradation of the electric cable and
move away from heat sources higher than 70°C.
After working, disconnect and roll up the cord in
the handle of transport of the compressor.
Do not use the machine with naked or wet feet.
Do not touch the compressor with wet hands.
Do not pull the cord to move the compressor or to
remove the plug.
Do not allow children to use the compressor.
Do not leave the compressor without monitoring
when it is connected; it can become source of
dangers.
The electric safety of this machine is assured only
when it is correctly connected with an efficient
grounding connection , as recommended in the
rules of electric safety requirements.
The responsibility for the manufacturer will not be
committed if grounding connection of the
installation is incorrect.
2 - INSTRUCTIONS, USES ADVICE
To obtain the best efficiency, please respect the
following indications:
- PLACE: Use the compressor indoors or under
shelter, do not expose it to the rain or near water
jets. Do not use the compressor in an explosive
atmosphere.
- VENTILATION: The compressor must be in a place
which allows ventilation, do not cover the
ventilation openings.
- TEMPERATURE: Use the compressor between
(+ 5°C and +35°C) (Otherwise, there are risks for
the electrical motor.)
- TENSION: Check that the sector tension and
tension indicated on the label are the same :
(Single phase:230 Volts - 50 Hz)
- HORIZONTAL SETTING: the compressor must be
installed on a horizontal plane, 10 ° angle is
allowable.
Check that the compressor has not been damaged
during the transport.
The switch must be in position «OFF».
Connect in a socket-outlet:
- Of 16 Amps under 230V.
- Connected to the ground.
- Connected to a differential protection.
- USING AN ELECTRIC EXTENSION:
- BEFORE USING:
Please only use an extension if absolutely
necessary.
We recommend the following dimensions: 5 meters
maximum length with section of wire of 2,5mm ².
Too small diameter wire sections and big lengths
would cause serious damage to the engine.
It is better to extend air pipe, which moreover will
give you stock of air.
- USE:
To start your compressor, it is necessary to:
Push the switch on position «ON».
NOTA: If you do not use the compressor, IT IS VERY
HIGHLY ADVISED to switch it «OFF».
As your compressor has no reserve, the air escapes
by the safety valve and damages the parts of the
compressor.
4 - MAINTENANCE
Your compressor is auto-lubricated (oilless), and
therefore does not require any maintenance apart
from the following points.
The operating of motor compressor should be
intermittent, it means 60% of use for 40% of
downtime.
Beyond this limit, the motor may overheat.
When overheated, the internal thermal protection of
the engine will work automatically by cutting the
electric current.
The motor will restart as soon as normal conditions of
temperature will be restored.
If you want to change tools,you have to stop the
compresseur.
ATTENTION!
For painting:
Use only low pressure spray guns.
Use your compressor according the different
applications accepted (inflation, air tools, painting,
washing with only water-based detergents, etc..),
Implies knowledge and compliance with standards
set for each job.
INSTALLATION AND SITE
INSTRUCTIONS
You have just bought your air compressor, it will give
you appreciable services.
Please ensure first that your compressor is powerful
enough, you may use it for:
- Inflating Tyres - Balloons - Swimming pools - Rafts
etc...... - Blowing / vacuum-cleaning / painting- Using
pneumatic tools :(ex. gun nailer, stapler, screw driver,
impact wrench, sand blasting, etc...)
Before use, it is imperative to read ENTIRELY the
present NOTE.
1 - INSTALLATION AND SITE
OPERATING INSTRUCTIONS
The compressor does not start:
- No electrical supply.
- The compressor is already pressurised,
disconnect the hose.
The compressor starts with difficulty:
- The electrical supply is insufficient.
- electrical supply cord is too long, or wire section
too small.
- Engine overload by cold weather.
- Electrical supply cord is cut or disconnected.
Abnormal noises, vibrations:
- loosened or worned parts.
- worned pump (mechanical noises).
- bad chocking of the compressor.
Low flow rate, pressure does not increase:
- suction filter is blocked.
- leaks in connection pieces.
- compression cylinder valves or inter-plate
gaskets broken.
- piston ring set worned.
5 - FAULTS / SOLUTIONS
3
How to choose the compressed air hose:
Use a rubber hose or a hose reinforced with safety
cable steel.
Do not use plastic hose,the temperature rises around
the cap connection, the plastic hose becomes soft
and exits from its setting.
In case of overheating
1 - Stop the compressor
2 - Before restart wait 5'
IDENTIFICATION STICKER OF THE PRODUCT
1 3 4 5 6
7
8
9
1
12
10
11 13
1 - Producer
3 - Power
4 - Tension- Phase Qty
and frequency.
5 - Maximum pressure
6 - Compressor weight
7 - Air delivery at 7 bar
8 - Revolutions per minute
9 - Measured noise level
10 - Serial number
11 - Code model
12 - Reference
13 - Year of manufacture
