61195868L1-13B, April 2005
Printed in the USA
Copyright 2005 Hewlett-Packard Development Company, LP
Quick Start Guide
5990-8864
ProCurve Secure Router dl 1xE1 Module
J8454A
1
X
E1 M
ODULE
C
OMMANDS
clock source [line* | internal]
Configures the source timing used for the interface.
line*
Recovers clock from the primary circuit.
internal
Provides clocking using the internal oscillator.
coding [ami | hdb3*]
Configures the line coding for the E1 physical interface. The settings must match the
line coding supplied on the circuit by the service provider.
ami
Specifies Alternate Mark Inversion.
hdb3
*
Specifies High Density Bipolar 3.
description <text>
Comment line to provide an identifier for this interface (for example, circuit ID, contact
information, etc.).
<text>
Shows up to 80 alphanumeric characters.
framing [crc4]
Configures the framing format of the E1 interface. This setting must match the framing
format provided by the service provider.
crc4
Enables CRC-4 framing.
loop-alarm-detect
Enables detection of loop alarms on the E1 interface. Use the
no
form of this command
to disable loop alarm detection. This setting is enabled by default.
loopback network [line | payload]
Initiates a loopback on the interface toward the network. Deactivate using the
no
loopback network
command.
line
Initiates a metallic loopback of the physical E1 network
interface.
payload
Initiates a loopback of the E1 framer (CSU portion) of the E1
network interface.
loopback remote v54
Initiates an E1 remote loopback test (with a V54 loopback pattern). Deactivate using
the
no loopback remote v54
command.
remote-alarm [rai* | ais]
Selects the alarm signaling type to be sent when a loss of frame is detected on the E1
receive signal.
rai*
Specifies Remote Alarm Indication.
ais
Specifies Alarm Indication Signal.
remote-loopback
Enables acceptance of remote loopback requests on this E1 interface. Deny
acceptance using the
no remote-loopback
command. This setting is enabled by
default.
sa4tx-bit [0 | 1*]
Assigns a value to the Tx spare bit in position 4.
show test-pattern
Shows the current test pattern error count.
shutdown
Turns off the interface. By default, all interfaces are disabled. Use the
no shutdown
command to enable the interface and allow it to pass data.
snmp trap link-status
Enables the interface to send SNMP traps when there is an interface status change
and controls the SNMP variable,
ifLinkUpDownTrapEnable
.
tdm-group
<group#> timeslots <DS0 range> speed [56 | 64]
Creates a group of contiguous DS0s on this interface to be used during the bind
process.
<group#>
Number label (1 to 1024) to identify this TDM group.
<DS0 range>
DS0s in this group in the form:
<starting DS0
-
ending DS0>.
56 | 64*
(Optional)
Specifies a channel rate of 56 kbps or 64 kbps.
test-pattern [clear | insert | ones | p511 | qrss | zeros]
Initiates sending the specified test pattern.
clear
Clears the test pattern error count.
insert
Inserts an error into currently active test pattern.
ones
Generates continuous ones.
p511
Generates repeating pattern of ones and zeros.
qrss
Generates a random pattern.
zeros
Generates continuous zeros.
ts16
Enables timeslot 16 multiframe to be checked on the receive signal.
* Indicates default values.
Note
This command list is an illustration of available
commands. For complete command descriptions and
default values, refer to the SROS Command Line
Interface Reference Guide provided on your ProCurve
SROS Documentation CD.
