3
PROBRITE.COM
Please call 1-844-507-5651 or email [email protected] for further assistance.
2
Visit
www.probrite.com/install
for installation video tutorials and product support
Table of Contents......................... 2
Safety Information....................... 2
Pre-Installation............................. 3
Planning Installation.................... 3
Specifications................................. 3
Tools Required............................... 3
Hardware Included........................ 4
Package Contents......................... 4
Installation..................................... 5
Installation (Extension Arm)...... 10
Operation ..................................... 14
Care & Cleaning........................... 15
Troubleshooting.......................... 15
Warranty....................................... 16
Table of Contents
Safety Information
IMPORTANT
THIS PRODUCT MUST BE INSTALLED IN ACCORDANCE WITH THE APPLICABLE
NATIONAL ELECTRICAL CODE AND LOCAL BUILDING CODES BY A PERSON FAMILIAR
WITH THE CONSTRUCTION AND OPERATION OF THE PRODUCT AND THE HAZARDS
INVOLVED.
PRECAUTIONS
☐
Please read and understand this entire
manual before attempting to assemble,
install, or operate this light fixture.
☐
This light fixture requires a 120-277Volt
AC power source.
☐
Some codes require installation by a
qualified electrician.
☐
This light fixture must be properly
grounded.
☐
Make sure connections are secure
using wire nuts, crimp-on lugs or other
approved connecting devices
☐
This light fixture should be installed
outdoors to a wall or a pole.
☐
This product may contain chemicals
known to be hazardous. Thoroughly
wash hands after installing, handling,
cleaning or otherwise touching the
product.
WARNING:
Turn the power off at the circuit
breaker or fuse. Place tape over the circuit
breaker switch and verify power is off at the
light fixture.
WARNING:
Risk of fire. Keep the lamp heads at
least 3 in. (76mm) from combustible materials.
CAUTION:
Burn hazard. Allow the light fixture
to cool before touching.
NOTICE:
For dimming use a 0-10V dimming
switch
Pre-Installation
PLANNING INSTALLATION
Before installing the light fixture, ensure that all parts are present. Compare parts with the
Hardware Included
and
Package Contents
sections. If any part is missing or damaged, do
not attempt to assemble, install, or operate this light fixture.
Estimated installation time:
20 minutes
SPECIFICATIONS
TOOLS REQUIRED
Phillips
Screwdriver
Wire strippers/
cutters
Circuit tester
Safety
goggles
Work
gloves
Silicone
Sealant
Ladder
NOTICE:
FCC Regulations state that any
unauthorized changes or modifications to
this equipment not expressly approved by the
manufacturer could void the user’s authoriza-
tion to operate this equipment.
MODEL
NOVA 100W
NOVA 150W
Lumens (Light Output)
12000 Lumens
18000 Lumens
Watts (Power Consumption)
100 Watts LED
150 Watts LED
Replaces
250 Watt PSMH
400 Watt Metal Halide
Lumens/Watts (Efficacy)
120 lumens per watt
120 lumens per watt
Power Requirements (Input Voltage)
120-277VAC
Light Color (CCT)
4000 Kelvins (Bright White)
Dimmable
Dimming (Use with 0-10V dimming switch)
Surge Protection
10kV
Optic Distribution Type
Type IV
Operating Modes
Dusk-to-Dawn:
Automatically turns light fixture ON during night
and OFF during day.
Switch-Controlled:
Flip switch to turn light fixture ON and OFF.
Use
included light sensor cap on fixture's light sensor
to utilize this mode setting.
Wrench
Power
Drill
INFORMATION:
The device is tested and found to comply with Part 15 of the FCC Rules. Operation is subject
to two conditions: (1) This device may not cause harmful interference and, (2) this device must accept any
interference received, including any interference that may cause undesired operation.
These limits are designed to provide reasonable protections against harmful interference when the
equipment is operated in a commercial environment.
