Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя

Страница: 58 / 132

Machine Manual

Orion

CTS Flex Stretchwrapper

Revision 3.0

System Operation

25 July 2016

Page 3-28

Multistretch Settings Screen

This is the Multistretch Settings (MIB) screen. This page is useful primarily to repair per-

sonnel when troubleshooting the machine.

Figure 3 - 21

The Multistretch

Screen

Table 3-20. The Multistretch Screen Button Descriptions

STATE 1

DESCRIPTION

ZERO TRIM

Press this button to modify the Zero Trim datapoint, in terms of milliamps. This

value determines at which point the Multistretch will begin paying out film as the

dancer bar is deflected. This value should be .5 mA higher than the Hall Effect Sen-

sor reading with the dancer bar at rest. Min - 3.mA Max - 8 mA

GAIN

Press this button to modify the Gain datapoint, in terms of percentage. This value

sets percentage of deflection of the dancer bar that is required for the Multistretch to

pay out film at maximum speed. Min - 10% Max - 100%

FILM TENSION

Press this button to modify the Film Tension datapoint, in terms of percentage. This

value limits the maximum speed at which the Multistretch will pay out film, which

creates tension. Min - 0% Max - 100%

HALL EFFECT SENSOR

This displays the current dancer bar Hall Effect Sensor reading, in terms of milli-

amps.

MODIFY SETTINGS

Press this button for access to modify the Zero Trim or Gain datapoints.

The Multistretch is disabled while modifying the datapoints.

APPLY SETTINGS

Press this button to accept the current Zero Trim and Gain datapoints and apply

them to the Multistretch. When complete, the drive will be enabled again.

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды