Pro Mach Orion CTS Flex Stretchwrapper Скачать руководство пользователя страница 21

Страница: 21 / 132

Orion

Machine Manual

Revision 3.0

CTS Flex Stretchwrapper

25 July 2016

Introduction and Safety

Page 1-11

Installation and First Time Power Up

Unloading

Machine can be easily unloaded and transported by a forklift with a minimum capacity of

2500 lbs.

Carefully insert the forks into the lifting tubes to the maximum possible depth.

Depending on the model, a forklift access may be either at the tower end of the

machine frame, the tower end or both. Look for the forklift tube access stickers shown

below.

Lift the machine (or other part of system) only to the necessary height to move it with

no bouncing or friction on the floor.

Sit the machine down assuring uniform contact with the floor, which is necessary to

ensure correct and smooth operation.

Figure 1 - 1

Fork Tube Access

Sticker

Содержание Orion CTS Flex Stretchwrapper





































































































































Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды

Pro Mach Orion CTS Flex Stretchwrapper, Руководство пользователя

Результаты поиска

Содержание Orion CTS Flex Stretchwrapper

Отзывы:

Похожие инструкции для Orion CTS Flex Stretchwrapper

Бренды по названию

Популярные бренды