manualshive.com logo in svg

Pro Lite LD64, Инструкция по установке, обслуживанию и эксплуатации

Поделиться
Скачать
Pro Lite LD64 Скачать руководство пользователя страница 4

After completion of installation, the method of operation should be demonstrated to the kitchen 
staff. The isolating switch location, for use in an emergency or during cleaning should also be 
pointed out. 
 

LD64 Oven 

The unit is designed to be connected to a single phase AC supply using the 2 metre mains lead fitted 
as standard.  

Check that no damage has occurred to the appliance, power cable and plug top during transit.   If 
damage has occurred do not use the appliance. 
Ensure that the mains power cable is routed free from the appliance to avoid damage. 
 We recommend supplementary electrical protection with the use of a residual current device 
(RCD).  Periodic testing, repair and fixed wiring connection should only be undertaken by a skilled 
and competent electrician. 

Wires are coloured in accordance with the following code and should be connected to the plug as 
follows: 

EARTH

 to terminal marked 

E

 or coloured 

GREEN

 or 

GREEN/YELLOW.

 

NEUTRAL

 to terminal marked 

N

 or coloured 

BLACK.

 

LIVE

 to terminal marked

 L

 or coloured 

RED.

 

Units which receive power from a plug, adaptor or distribution board must be individually protected 
by a fuse with an appropriate rating. (see technical information) 
 
Any replacement supply cable must be 1.5mm2•, cord code designation 245 IEC 57 (CENELEC H05 
RN-F). 
For internal connection, outer sheathing must be stripped 140mm from the cable end. The live and 
neutral conductors must be trimmed so that the Earth conductor is longer by 50mm. Pass inlet cable 
through the rear panel cord grip and ensure that the cable is routed without leaving excessive free 
length inside the appliance. 
 

SECTION 3 - USING AND CLEANING PRO-LITE UNITS 
 

IMPORTANT: GENERAL NOTES ON CLEANING 

Disconnect unit from electricity supply prior to cleaning 
Never use a coarse abrasive to clean exterior panels. A soft cloth with a warm 
water and detergent solution is sufficient. 
Never attempt to steam clean a unit or hose it down with a jet of water. 

 

LD64 Oven 
 
 
             Mains Neon         

 

 

 

 

 

 

 

Thermostat 

 

 

 

 

 

 

 

 

 

 

 

Neon 

 
 
 
 
 

 
Thermostat Control Knob 

 
 
 

Содержание LD64









Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды