Pro-Lift T-3101, Инструкция по эксплуатации и каталог запасных частей

Страница: 2 / 4

2 3
Save these instructions. For your safety,
read and understand the information con -
tained within. The owner and operator shall
have an understanding of this product and
safe operating procedures before attempt -
ing to use this product. Instructions and
safety information shall be conveyed in the
operator’s native language before use of
this product is authorized. Make certain that
the operator thoroughly understands the in -
herent dangers associated with the use and
misuse of the product. If any doubt exists as
to the safe and proper use of this product as
outlined in this factory authorized manual,
remove from service. Inspect before each
use. Do not use if broken, bent, cracked
or otherwise damaged parts are noted. If
the engine stand has been or suspected to
have been subjected to a shock load (a load
dropped suddenly and unexpectedly upon
it), discontinue use until checked out by an
authorized factory service center. Owners
and operators of this equipment shall be
aware that the use of this equipment may
require special training and knowledge. It
is recommended that an annual inspection
be done by qualified personnel and that
any missing or damaged parts, decals,
warning/safety labels or signs be replaced
with factory authorized replacement parts
only. Any engine stand that appears to be
damaged in any way, is worn or operated
abnormally shall be removed from service
immediately. Labels and owner’s manu -
als are available from manufacturer (see
Replacement Parts, page 5).
PRODUCT DESCRIPTION
Pro-Lift Engine Stands are designed to
safely support rated capacity engines.
Welded steel tube construction, heavy
gauge steel plate head plates and mount -
ing arms along with compliance with fac -
tory standards ensure safety, strength and
stability.
BEFORE USE
1. Inspect stands before each use. Do
not use if bent, broken or cracked
components are noted. Ensure that
casters/wheels and head plate rotate
freely. Check for and tighten any loose
assemblies.
2. Verify that the product and the applica -
tion are compatible.
3. Before using this product, read the own -
er’s manual completely and familiarize
yourself thoroughly with the product
and the hazards associated with its
improper use.
Figure 1 - Typical Engine Stand
Nomenclature
Figure 2 - Assembly illustration for model
T-3101
ASSEMBLY
Model: T-3101 ( see Figure 2 )
Important:
Reference numbers are for
assembly purpose only. See replacement
parts illustration for ordering replacement
parts.
1. Attach 2 front casters (Ref. No. 15) using
the lock washers (Ref. No. 13) and nuts
(Ref. No. 12).
2. Attach 2 rear wheels (Ref. No. 3) using
the washers (Ref. No. 2) and snap-rings
(Ref. No. 1).
3. Attach upright (Ref. No. 16) to the rear
leg (Ref. No. 4) using the M12 x 80 bolt
(Ref. No. 5), washer (Ref. No. 6), lock
washer (Ref. No. 7) and finally the hex
nut (Ref. No. 8).
4. Attach the center beam (Ref. No. 10) to
the front leg assy. (Ref. No. 11) using
two M12 x 80 bolts (Ref. No. 5), lock
washer (Ref. No. 7) and hex nut (Ref.
No. 8).
5. Slide mounting plate (Ref. No. 20) into
the collar portion of the upright (Ref. No.
16), align rotating position holes and
insert lock pin (Ref. No. 17).
6. Attach the four mounting adapter arms
(Ref. No. 21) to the slotted portion of the
mounting plate (Ref. No. 20) using M14
x 60 bolts (Ref. No. 22), lock washers
(Ref. No. 14), flat washers (Ref. No. 13)
and hex nut (Ref. No. 12).
7. Insert handle (Ref. No. 19) into the hole
in the stem portion of the mounting plate
(Ref. No. 20) which protrudes from the
rear of the collar of the upright (Ref.
No. 16).
8. Attach the handle grips (Ref. No. 18)
onto both ends of handle (Ref. No. 19).
Study, understand, and follow all instruc -
tions provided with and on this device. Do
not exceed rated capacity. Use only on
hard, level surface. Never put any por -
tion of your body under engine when it is
supported by the engine stand. Use only
hardened, appropriately sized bolts to se -
cure engine to stand. Center the engine
on mounting plate and ensure attaching
hardware is tightly fastened. Off center
loading may cause the engine to rotate
unexpectedly and cause the loaded stand
to tip over. Lock mounting plate rotating
mechanism before beginning engine
service. Unlock rotating mechanism
slowly and carefully. Do not modify or
alter this product. Do not use this device
for any purpose other than that for which
it is intended. Failure to heed these mark -
ings may result in personal injury
!
WARNING
!
rotating
mechanism
lock pin
handle
head plate
mounting arm
rear leg
center beam
front caster
front leg
rear wheel
upright